NT3881D
Dot Matrix LCD Controller and Driver
Features
!
Internal LCD drivers
16 common signal drivers
40 segment signal drivers
(can be externally extended to 400 segments
using NT3882)
!
Maximum display dimensions
40 characters * 2 lines or
80 characters * 1 line
!
Interfaces with 4-bit or 8-bit MPU
!
Versatile display functions provided on chip:
Display Clear, Cursor Home, Display ON/OFF,
Cursor ON/OFF, Character Blinking, Cursor
Shift, and Display Shift
!
Three duty factors, selected by PROGRAM:
1/8, 11/11, and 1/16
!
Displays Data RAM (DD RAM): 80 X 8 bits
(displays up to 80 characters)
!
Character Generator RAM (CG RAM):
64 X 8 bits for general data,
8 5 X 8 programmable dot patterns, or
4 5 X 10 programmable dot patterns
!
Low voltage reset
!
NOVATEK Identification code
!
Bonding option for A-type and B-type waveform
!
Character Generator ROM (CG ROM):
3 kinds of CG ROM sizes:
192 characters:
160 5 X 8 dot patterns
32 5 X 10 dot patterns
240 characters:
192 5 X 8 dot patterns
48 5 X 10 dot patterns
256 characters:
192 5 X 8 dot patterns
64 5 X 10 dot patterns
Custom CG ROM is also available
!
Built-in power-on reset function
!
Logic power supply: single +5V supply
!
LCD driver power supply: V
1
- V
5
(V
DD
+0.3 - V
DD
-13.5)
!
Three oscillator operations
(Freq. = 250KHz - 270KHz):
•
Internal oscillation
•
Ceramic resonator
•
External clock
!
CMOS Process
!
Available in 80-pin QFP or in CHIP FORM
General Description
The NT3881D is a dot matrix LCD controller and driver
LSI that can operate with either a 4-bit or an 8-bit
microprocessor (MPU). NT3881D receives control
character codes from the MPU, stores them in an internal
RAM (up to 80 characters), transforms each character
code into a 5 X 7, 5 X 8, or 5 X 10 dot matrix character
pattern, and then displays the codes on the LCD panel.
The built-in Character Generator ROM consists of 256
different character patterns.
The NT3881D also contains Character Generator RAM
where the user can store 8 different character patterns at
run time. These memory features make character display
flexible. NT3881D also provides many display instructions
to achieve versatile LCD display functions. The NT3881D
is fabricated on a single LSI chip using the CMOS
process, resulting in very low power requirements.
With several NT3882 driver ICs connected to the
NT3881D, up to 80 characters can be displayed.
1
V2.4
NT3881D
Pin and Pad Descriptions
Pin and Pad No.
1 - 22
24, 25
Designation
SEG22 - SEG1
OSC1, OSC2
I/O
O
External
Connection
LCD panel
Description
Segment signal output pins
Pins connected to resistor or ceramic filter for
internal clock oscillation. For external clock
operation, clock inputs to OSC1.
P
O
O
P
Power supply
NT3882
NT3882
Power supply
Power supply for LCD driver
Clock to latch serial data D sent to NT3882.
Clock to shift serial data D
V
DD
: +5V
A-Type waveform: V
DD
bond to VDDA
B-Type waveform: V
DD
bond to VDDB
23
34
GND
M
P
O
Power supply
NT3882
GND: 0V
Switch signal to convert LCD drive waveform to
AC
Character pattern data corresponding to each
common signal is transmitted serially from this
output. 0-Non selection, 1-selection.
Register select signal
0: Instruction register (write)
Busy flag, address counter (read)
1: Data register (write, read)
Read/Write control signal
0: Write
1: Read
Read/Write start signal
Lower 4 tri-state bi-directional data bus for
transmitting data between MPU and NT3881D.
Not used during 4-bit operation.
Higher 4 tri-state bi-directional data bus for
transmitting data between MPU and NT3881D.
DB7 is also used as busy flag.
Common signal output pins
Segment signal output pins
26 - 30
31
32
33, 81
V
1
- V
5
CL1
CL2
VDDB, VDDA
35
D
O
NT3882
36
RS
I
MPU
37
R/W
I
MPU
38
39 - 42
E
DB0 - DB3
I
I/O
MPU
MPU
43 - 46
DB4 - DB7
I/O
MPU
47 - 62
63 - 80
COM1 - COM16
SEG40 - SEG23
O
O
LCD panel
LCD panel
5
V2.4
京公网安备 11010802033920号
EEWORLD
