EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

MBA0204VE2181CCT00

Description
RESISTOR, THIN FILM, 0.25 W, 0.25 %, 15 ppm, 2180 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size166KB,10 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

MBA0204VE2181CCT00 Overview

RESISTOR, THIN FILM, 0.25 W, 0.25 %, 15 ppm, 2180 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT

MBA0204VE2181CCT00 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1774101288
package instructionAxial,
Reach Compliance Codecompliant
Country Of OriginCzechia
ECCN codeEAR99
YTEOL7.2
Other featuresPRECISION, LASER TRIMMABLE, RATED AC VOLTAGE (V): 200
structureTubular
JESD-609 codee3
Lead diameter0.5 mm
Lead length29 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package diameter1.6 mm
Package length3.6 mm
Package shapeTUBULAR PACKAGE
Package formAxial
method of packingAMMO PACK
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineCECC40101-806
resistance2180 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyMETAL FILM
Temperature Coefficient15 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWIRE
Tolerance0.25%
Operating Voltage200 V
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ask about the interrupt response speed
Hello everyone, I have been busy with the WM project recently and have not been online for a long time. I encountered a problem today and I would like to ask you for help. I hope you can give me some ...
huzhiming Embedded System
LM2576 output current problem
Dear experts: I have a question. When I use LM2576S-5.0 as a voltage regulator, why is the output current not 3A, but only 50MA? Please advise! The circuit diagram is attached....
fy_1970 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 370  1284  960  2648  743  8  26  20  54  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号