Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
I have an image compression algorithm that I want to port to a DSP+ARM (674x core + cortex a8) platform. ARM is mainly used for control, and DSP is used for image compression processing. The ARM runs ...
New key scanning program However, I have been browsing the Internet for a long time and have read a lot of source code, but I have not found any trace of this key processing method. Therefore, I will ...
I got the ST Nucelo F091RC development board a few days ago, but I haven't had time to do it. Today I'll post something special for your reference. Use ordinary LEDs to realize LED display and light i...
[color=#333333][size=14px]Although uPyCraft is convenient, it cannot freely select the firmware version and can only download DF's own firmware. DF's firmware version is lower and lacks some functions...
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1 Introduction
The stepper motor is an actuator of an open-loop servo motion system, which is controlled in a pulse mode and outputs angular displacement. Compared with AC servo motors and DC servo ...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
With the rapid development of information technology represented by computers, semi-physical simulation technology plays an important role in many military and civilian fields such as aerospace and co...[Details]
At present, products in the field of monitoring generally focus on the field level, that is, the client/server (C/S) model is adopted, the purpose of which is to ensure the stability and reliability o...[Details]
System Block Diagram
The system uses DSP56F826 chip as the core control module and CMOS digital image sensor chip. The image acquisition resolution can reach 640×480 pixels. When high-re...[Details]
This article examines some of the requirements that need to be met when designing DC/DC converters used in telecom and distributed power systems (DPS). Telecom DC/DC converters have an input voltag...[Details]
1. Explanation of some common English abbreviations in ARM
MSB: most significant bit;
LSB: least significant bit;
AHB: Advanced High-Performance Bus;
VPB: VLSI peripheral bus th...[Details]
introduction
ISP in-system programmable technology is different from the previous PLD which requires a dedicated burner to realize logic design. It does not need to remove the ISP device to re...[Details]
1. Introduction
The human balance ability is the basis for people to carry out various sports. People need balance ability to stand, sit, lie down, and walk. Once a person's balance ability is...[Details]
1 Introduction
Smart cars are the embodiment of the cross-integration of multiple disciplines such as automotive electronics, artificial intelligence, pattern recognition, automatic control, c...[Details]
Abstract: Based on CPLD as the core, a manageable SAS hard disk backplane is designed. While conveniently replacing the faulty hard disk, it can indicate the working status of the hard disk by cont...[Details]
When a car driven by an ignition engine runs on the road, the high-voltage ignition system of the gasoline engine will generate strong electromagnetic waves, which will interfere with the normal opera...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
