Abstract: The characteristics, system structure, design method and production of low noise amplifier and image suppression mixer when low noise GaAs FET is used as single pulse tracking radar front en...
Teacher, we are now writing programs related to stepper motors. The forward and reverse programs of stepper motors have been written. Next, we will write a program for stepper motors to draw straight ...
Author: Zhan Jun 1. Definition of I2C bus terms Term Description Transmitter A device that sends data to the bus Receiver A device that receives data from the bus Master A device that initiates transm...
Can anyone tell me why using MCU to control a switching power supply is better than using a general switching power supply? Tell me about its advantages, hey, thank you very much!...
[i=s]This post was last edited by xusiwei1236 on 2022-5-14 22:51[/i][Xianji HPM6750 Review] CoreMark running test
In the previous post, we completed the construction of the Embedded Studio development...
-------Detailed explanation of Protel 99 SE PCB layer The main content of this post is extracted from the book "Advanced Application of Protel 99" by Tiger Studio, and appropriate amendments have been...
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
1 Introduction Due to the special working environment of coal mine production, the production process is more dangerous and unsafe than the general industry. With the continuous increase in c...[Details]
Every era has anxiety that has nowhere to go. Let's follow the embedded editor to learn about the relevant content.
The anxiety of the post-Internet era is that if you don’t revolutionize ...[Details]
According to TechRadar, given rumors that
Google
is developing a Pixel Watch
,
the
recently renamed Wear OS
smartwatch
operating system may soon be able to show its full cap...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
environment: Host: XP Development environment: MDK4.23 MCU:STM32F103CBT6 illustrate: Collect AD through pins PA1 and PA2. Collect AD 10 times for each channel. #include "ad_driver.h" //Global ...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
/*----------------------------------------------- Name: IIC protocol PCF8591 AD/DA conversion Content: Use DA input, digital tube display output digital quantity, LED display analog voltage size ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
On November 23, Toyota recently released its latest humanoid robot, the T-HR3, which the company said "represents an evolution of the humanoid robot played by previous devices ". This new robot was...[Details]