EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342H07B14B2MT3M

Description
Fixed Resistor, Thin Film, 0.25W, 14200ohm, 100V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342H07B14B2MT3M Overview

Fixed Resistor, Thin Film, 0.25W, 14200ohm, 100V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP

D55342H07B14B2MT3M Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid260347692
package instructionCHIP
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.35
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance14200 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Multi-pulse generation
How to generate multiple pulses with a frequency of 200KHZ...
phdwong FPGA/CPLD
How to display the full waveform when the op amp is controlled by a single power supply
At first I used the same-phase amplifier but did not solve the midpoint problemThe effect is like this Later, I processed the midpoint by changing the ground wire of R2 to VCC/2 in theory. The effect ...
ligongxiaobie Analog electronics
LED life issues
If LEDs are stored at room temperature for a year and a half, can they be shipped as new products? What are the impacts?...
zhu_john LED Zone
How can I make the components white when printing the schematic in Word?
In protel, the components are yellow. After printing in word, the components are a little darker. It's just a little darker. Our teacher is not happy with it and insists on using hollow ones! I said t...
zxpla PCB Design
Discussion on Several Key Issues in Power Supply Design
(1) Selection of the average value of high-frequency pulse output voltage wave udo,avg   When the DC/AC inverter is under DPM control, its essence is to combine the high-frequency pulse voltage wave u...
zbz0529 Power technology
How can I set the line spacing and character spacing of a font?
How can I set the line spacing and character spacing of a font? In addition, when setting the font height value, is the value passed in logical units? How can I convert a font that I want to specify i...
katrina Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2307  2701  2200  351  1641  47  55  45  8  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号