EEWORLDEEWORLDEEWORLD

Part Number

Search

3KH28/1CDD12

Description
Card Edge Connector, 56 Contact(s), 2 Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Green Insulator, Receptacle
CategoryThe connector    The connector   
File Size420KB,4 Pages
ManufacturerEaton
Download Datasheet Parametric View All

3KH28/1CDD12 Overview

Card Edge Connector, 56 Contact(s), 2 Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Green Insulator, Receptacle

3KH28/1CDD12 Parametric

Parameter NameAttribute value
Objectid1225932419
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL6.5
body width0.33 inch
subject depth0.437 inch
body length4.305 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationAU ON NI
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleBELLOWED TYPE
Dielectric withstand voltage1500VDC V
maximum insertion force4.448 N
Insulation resistance5000000000 Ω
Insulator colorGREEN
insulator materialDIALLYL PHTHALATE
MIL complianceYES
Manufacturer's serial numberCDD
Plug contact pitch0.125 inch
Match contact row spacing0.145 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing3.683 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityMIL-C-21097
Terminal length0.195 inch
Terminal pitch3.175 mm
Termination typeSOLDER
Total number of contacts56
Evacuation force-minimum value.278 N
【Case Study】 Rigol spectrum analyzer base station signal test and Bluetooth frequency hopping signal test
When a laboratory in Xi'an was testing signals, it was found that the data always had relatively high bottom noise. Xi'an Antai test engineers suspected that there were radio transmitters around the l...
安泰测试设备 Test/Measurement
Analog Discovery 2 Review (6) Waveform Generator
[i=s]This post was last edited by cruelfox on 2019-12-8 12:17[/i]  In the previous article Analog Discovery 2 Review (5) Acquisition System Hardware Analysis , I introduced the analog/digital conversi...
cruelfox Test/Measurement
About STM32F103 GPIO operation and ODR, BRR, BSRR settings
When I was developing products using the stm32F103 series recently, some strange problems occurred during GPIO operations. The description is as follows:1. Using ODR to operate the PC port, because th...
吴通凯 stm32/stm8
Serial port configuration problem
8 data bits, 1 stop bit, no parity bit, how should ioctl be set specifically? Thank you!...
lnx Embedded System
Share: How to lay out a circuit board for an op amp
[size=4] During the circuit design process, application engineers often overlook the layout of the printed circuit board (PCB). A common problem encountered is that the circuit schematic is correct, b...
qwqwqw2088 Analogue and Mixed Signal
Using ADS software to adjust the flashing problem of the button trigger light
Now I want to use ads to adjust a simple program to trigger the light to flash. The existing program only has one phenomenon, Led_Display(0xff); the light on the ARM9 board turns on, and the 0x00 ligh...
pcshow Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2626  2312  504  2599  1868  53  47  11  38  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号