DG408/DG409C_ ................................................0°C to +70°C
DG408/DG409D,E_ .........................................-40°C to +85°C
DG408/DG409AK ..........................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1:
Signals on S_, D_, EN, A0, A1, or A2 exceeding V+ or V- are clamped by internal diodes. Limit forward current to
maximum current ratings.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ISO EMM series DC current signal isolation amplifier products adopt low-cost, small-volume (SIP 8Pin) design solutions, which are very convenient to use. They are free of zero-point shunting and gain ...
I am going to use the CAN bus recently. I have three boards with CAN transceiver PHY, a TMS320F28377S LAUNCH, a GD32VF103V EVAL, and a MM32 eMiniBoard. I remember that I had a small board with CAN PHY...
I have a question. I have written the driver for my serial port 1 under uclinux and transplanted it to 44b0. The serial port 0 has its own driver. Now the problem is, I can't figure out how to connect...
I'm decoding a set of data recently, and the data checksum is the last two bytes. Can you help me think about what calculation methods are generally used for two-byte checks? For example, there is a d...
In our common sense, the word technology often has two definitions. The first is the technology sealed in the laboratory. They are like flowers on the mountain top. Only a few people on the mountai...[Details]
The trade war between China and the United States has become the focus. The United States has begun to play the ban card against Chinese technology companies. The ZTE incident shows that if the ban...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
Since China began to try to produce panels independently in 1998, in 2018, China's panel industry has gradually upgraded from a marginal industry to the largest production scale. Especially in the ...[Details]
Unlike three years ago, today's
artificial intelligence
is no longer just a floating concept, and the venture capital circle has begun to explore the various possibilities of this technolog...[Details]
I rewrote the main part of this program. The program uses the watchdog as a normal timer and scans the digital tubes in the watchdog interrupt. In addition, I added a display buffer. If you want to d...[Details]
STM32 uses FSMC to read and write CPLD programs. CPLD is hung on the address line and data line of STM32. CPLD is regarded as an off-chip RAM for reading and writing. On the board I made, CPLD is hun...[Details]
ADC Introduction: ADC (Analog-to-Digital Converter). That is, converting analog signals into digital signals for processing. When storing or transmitting, analog-to-digital converters are almost ...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
The first one is a DMA mode of multiple channel acquisition void ADC_DMA_Config(void) { ADC_InitTypeDef ADC_InitStructure; RCC_HSICmd(ENABLE); while (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET); ...[Details]
Requirements: Set timer T1 as an external event counter, count 500 pulses every time, then switch T1 to timing mode and output a positive pulse with a width of 10ms at P1.2. Over and over again. A...[Details]
The concept of AI is general and covers a wide range. What is the core of AI? Let's follow the network communication editor to learn about the relevant content.
On May 8, local time in the...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
