MAFA 1000 Series Erbium Doped Fiber Micro Amplifier
EMCORE’s MAFA 1000 Series Erbium Doped Fiber micro Amplifier (μEDFA)
Gain Block Module is an ideal building block for OEM system integrators. The
family of MAFA 1000 EDFA Gain Blocks is designed to meet the most demanding
noise performance requirements of fiber optic communications and control
systems, and performs all the functions required of an optical amplifier for system
integration.
MAFA 1000 series EDFA Gain Blocks provide input and output optical isolation for
stable, low noise operation. The input and output optical signal power levels are
detected for monitoring and control. The input optical signal is amplified with
active gain control for a constant output power level or with active output power
control for constant gain mode operation.
The MAFA 1000 series EDFA Gain Blocks also provide monitors and associated
alarms for all critical operating parameters. The optical output of the MAFA 1000
series EDFA Gain Blocks can be split into multiple ports by optional external
splitter. Optional back reflection monitoring feature enables safe output optical
power managing.
The compact mechanical footprint of the MAFA 1000 allows using this unit to be
installed in small space environments.
Applications
CATV Systems
Long Distance RF/Microwave Fiber
Optic Communication Links
Sensing and Control Systems
High Performance Supertrunking Links
High Power Distribtuion Networks
Redundanct Ring Architectures
FTTx Networks
Features
Full Function Fiber Optic Amplifier
Ready for Integration
Low Noise Figure (Typ < 4.5 dB)
Pin: -6 dBm to +12 dBM
Pout: +14 dBm to +23 dBm
RS-232 Monitor and Control Interface
(SNMP V.1 is also possible)
Standard and Optional Gain Flatness
Low Electrical Power Consumption
Input/Output Isolation >40/40 dB
Polarization Dependant Gain < 0.1 dB
Polarization Mode Dispersion < 0.2 ps
Input & Output Return Losses < -40 dB
Output Residual Pump Power < -30 dBm
Back Reflection Monitoring
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Optical/Electrical Characteristics
1
Property
Unit
Limit
1014
Operating Input Power
Operating Input Power
Output Power
Noise Figure
Static Gain Flatness
Dynamic Gain Flatness
Output Power Stability
Power Consumption
(Steady state)
Pin (dBm)
Pin (dBm)
Po(dBm)
NF (dB)
ΔGs
(dB)
ΔGd
(dB)
(dB)
Psys(W)
Max
Min
Nominal
Typ
Max
Max
Max
Max
12
-6
14
+/-.25
4.0 dB
+/-0.5
+/-1.0
+/- 0.1
2
Models
1017
12
-6
17
+/- .25
4.0 dB
+/-0.5
+/-1.25
+/- 0.1
3
Comments
1022
12
-6
22
+/- .25
4.0 dB
+/-0.5
+/-2.0
+/- 0.1
6
1020
12
-6
20
+/- .25
4.0 dB
+/-0.5
+/-1.5
+/- 0.1
5
1023
12
-6
23
+/- .25
4.0 dB
+/-0.5
+/-2.0
+/- 0.1
8
Typical
(May vary for some models)
Note 2
@ Pin = 0 dBm, no Pin monitoring
(Notes 3, 7, 8)
(Notes 4)
(Notes 5, 7)
(Note 6)
70 C Case
o
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
0 dBm. Measuring with 1 input optical signal with Pin
≈
0 dBm and
≈
1550 nm is also available
4. Measured with a swept Probe Signal (Pp), where Pp
≈
0 dBm @ 25C
5. Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ ~ 1550 nm; (Pt
≈
Pp+20 dB; Pt + Pp
≈
0 dBm)
@ 25C; Gain Flattened Options with
ΔG ≤
+/-0.75dB or
ΔG ≤
+/-1.0dB are available (for
some models and for defined
input optical power only)
6. Over polarization and temperature
7. Specific
ΔG
can be guaranteed at a single specified Input Optical Power Level (Pin = Pt + Pp) equal or different from 0
dBm
8. If input power monitoring and input isolation are required then typical NF (Typ) for all units @ Pin = 0 dBm as
4.5 dB
General and Mechanical Specifications
Property
Operating Wavelength
Operating Case Temperature
Storage Temperature
Operating Humidity
Voltage Supply Range
Optical Connectors
Dimensions (mm)
Requirement
1532nm ~ 1565nm
0C to 50C
-40C to 85C
20% to 85%
+12VDC/+5VDC/+3.3VDC
SC; FC; E2000
70 x 90 x 15
Comments
Standard
Standard*
Standard
Non-condensing
All versions**
User Specified
All versions
* - Extended temperature range of –40C to +75C is also possible
** Transient Pulse to +X.XVDC + 5% for < 100 msec
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Outline Drawing (dimensions in mm)
Compliance and Reliability Information
FCC: Subpart B. Part 15 class “A”: Unintentional Radiators
EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits
and methods of measurements – Electric Field Radiation Emissions (2001)
Fit Rate: 90% level of confidence - 290 @ 25C
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA1014-SC-00-S-2: 14 dBm gain block with SC/APC optical connectors, standard NG/GF, standard temperature range,
+5VDC power supply
Note:
Only some models can be order with Gain Flattened options. (-01 suffixes).
Please contact your Sales Representative
for details
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Laser Safety Information
This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IV laser product based
on the maximum optical output power shown below. During use as intended, the laser energy is fully contained within the
fiber network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product.
The laser product report has been submitted to the CDRH and the accession number is expected by October 2006.
Wavelength = 1535 ~ 1565 nm (dependant on input source)
Maximum Output Power = 0.2 W (single output, 23 dBm model)
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Hey everyone in the forum, I have a question for you!
I have just started embedded development and I don’t know a lot of things. For embedded ARM development based on LINUX, I really don’t know where ...
This article discusses four commonly used FPGA/CPLD design ideas and techniques: ping-pong operation, serial-to-parallel conversion, pipeline operation, and data interface synchronization. They are al...
The ADC chip is AD7656. The waveform is normal when the frequency is 5khz. Now when the frequency rises to 10khz, the waveform intermittently appears as shown in the figure. Please give me some advice...
Should stepper motors be considered DC motors? Can I use only one 298 as the driver? I checked online and many people said it is possible, but why does the teacher say it is wrong?...
Section 1: Mood and ClockTo be honest, I don't have many microcontrollers that I can use. I always think that any microcontroller can develop a good product.In the past few years, I used 51 and always...
On August 23rd, Geely's subsidiary, Jiyao Tongxing, announced it has the industry's largest advanced production capacity for tandao
batteries
, with eight production bases across China. Jiy...[Details]
When you are happily watching NBA or football, your wife asks you to turn off the lights in the bedroom. Would you be depressed? Of course, unless you are not afraid of your wife.
Now you are ...[Details]
ISP devices, such as field programmable devices (FPGAs and CPLDs), do not require a programmer. Using programming kits provided by the device manufacturer, they employ a top-down modular design app...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
The fracture mechanism is stress concentration, which typically occurs at the capacitor lead pins or pad connection points, as shown in the figure. Under vibration, the capacitor lead pins and pad ...[Details]
Batteries are a core component of new energy vehicles, accounting for over 40% of the total cost. This is also the area where automakers are most willing to tamper with costs. Since 2021, domestic ...[Details]
For the average person, an electricity meter is a monthly bill. For beginners, it's a collection of components and parts. For experienced meter engineers, however, it's a complex and complex proces...[Details]
Generally not, but there are exceptions. For example, a torque motor controller with three-phase output voltage imbalance can cause current imbalance, similar to a phase loss. However, only two pha...[Details]
Recently, I received a request to use OK1028A-C to output PWM square wave. However, I found that there was no relevant instructions on the OK1028 platform, so I started writing this article.
A...[Details]
On August 19, Huawei's Executive Director and Chairman of the Device BG, Richard Yu, shared a Weibo post about a conversation he had with a Zunjie S800 owner. The owner had driven over 5,000 kilome...[Details]
Charge your electric car for just six minutes and you'll get 1,000 kilometers! This isn't just a scene from a science fiction film, but a reality made possible by Guoxuan High-Tech's Jinshi solid-s...[Details]
Servo motors, also known as actuator motors, serve as actuators in automatic control systems, converting received electrical signals into angular displacement or angular velocity output on the moto...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
