EEWORLDEEWORLDEEWORLD

Part Number

Search

PT7M6834GD2TA3E

Description
Ultra Low Voltage Detectors
File Size378KB,12 Pages
ManufacturerPericom Semiconductor Corporation (Diodes Incorporated)
Websitehttps://www.diodes.com/
Download Datasheet View All

PT7M6834GD2TA3E Overview

Ultra Low Voltage Detectors

|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
PT7M6832-6840
Ultra Low Voltage Detectors
Features
Factory-Set Reset Threshold Voltages for Nominal
Supplies from 1.2V to 1.8V
Low power consumption : Typ 7.5μA
Five different timeout periods available: 70μs(voltage
detector), 1.5ms, 30ms, 210ms and 1.68s
Output configuration: Push-pull RESET , push-pull
RESET or open-drain RESET
Guaranteed reset valid to Vcc: 0.9V--active low,
0.85V--active high
Detect voltage accuracy:
1.5%
Adjustable threshold reset-in option
Immune to short negative Vcc transients
Small SOT23-3L, SC70-3L or SOT143-4L packages
Description
The PT7M6832–6840 are microprocessor (µ
P)
supervisory circuits used to monitor low-voltage power
supplies in µ and digital systems. They provide
P
excellent circuit reliability and low cost by eliminating
external components and adjustments when used with
+1.2V to +1.8V powered circuits.
These devices assert a reset signal whenever the VCC
supply voltage declines below a preset threshold or
whenever manual reset (MR) is asserted. Reset remains
asserted for a fixed timeout delay after VCC has risen
above the reset threshold or when manual reset is
deasserted. Five different timeout periods are available:
70µ (voltage detector), 1.5ms, 30ms, 210ms, and 1.68s.
s
Reset thresholds suitable for operation with a variety of
supply voltages are available.
The PT7M6832/PT7M6835/PT7M6838 have a push-
pull active-low reset output (RESET). The PT7M6833/
PT7M6836/PT7M6839 have a push-pull active-high
reset output (RESET) and the PT7M 6834/ PT7M 6837/
PT7M 6840 have an open-drain active-low reset output
(RESET). The open-drain active-low reset output
requires a pull-up resistor that can be connected to a
voltage higher than VCC.
The PT7M6835/PT7M6836/PT7M6837 feature a
debounced manual reset input (MR), while the
PT7M6838/PT7M6839/PT7M6840 provide a RESET-
IN input allowing the user to externally adjust the reset
threshold. The reset comparator is designed to ignore
fast transients on VCC.
Low supply current of 7.5µ makes the PT7M6832–
A
PT7M6840 ideal for use in portable equipment. These
devices are available in 3-pin SOT23 or 4-pin SOT143
packages.
Pad Configuration
PT7M6832
PT7M6833
PT7M6834
1
GND
1
PT7M6832
PT7M6833
PT7M6834
GND
VCC
3
VCC
3
2
RESET (RESET)
2
RESET (RESET)
SOT23-3L
() is for PT7M6833
SC70-3L
() is for PT7M6833
PT7M6835
PT7M6836
PT7M6837
1
GND
RESET
(RESET)
4
1
PT7M6838
PT7M6839
PT7M6840
GND
RESET
(RESET)
4
Applications
Computers
Controllers
Intelligent Instruments
Critical μP and μC Power Monitoring
Portable/Battery-Powered Equipment
2
VCC
MR
3
2
VCC
RESET-IN
3
SOT143-4L
() is for PT7M6836
SOT143-4L
() is for PT7M6839
2013-11-0003
1
PT0236-6
11/18/13
Waveform data generation tools (sine, triangle, sawtooth, square wave)
[i=s]This post was last edited by paulhyde on 2014-9-15 03:11[/i]Waveform type: sine, square, triangle, sawtooth; Data width can be set; Data length can be set; Data storage type can be set;...
水木秋寒 Electronics Design Contest
Oscilloscope progress (continuously updated...)
1. All components before soldering: 2. Since some components have not been purchased yet, only some components have been soldered:...
caihong0217 DIY/Open Source Hardware
Received ARM7 development board
First of all, I would like to thank SOSO and Fengzheng for the ARM7-LPC development board. The courier was very good and it arrived in one day. Here are some beautiful photos of the development board....
billbot501 ARM Technology
Brief introduction to nand flash driver writing steps under Linux
[align=left][font=宋体]As mentioned above, when [/font]nand_scan_tail, the system will use the default system function based on your driver. If some functions are not implemented, then use your own func...
13691982107 Linux and Android
How should we solve problems encountered during programming?
When writing programs, we often encounter various problems, such as the LCD not lighting up. How should we find the cause when encountering a problem? As a novice, we always don't know where to start?...
junyingxiu Microchip MCU
Typical electronic design routines Typical electronic design routines
Typical electronic design routines Typical electronic design routines...
wangwei20060608 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 565  1139  2402  674  2762  12  23  49  14  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号