required per UL 508A for feeder circuit applications
and per NEC for field installations.
To increase application flexibility, these blocks
feature dual-wire rated ports that accept copper or
aluminum conductors while retaining a UL Listed
status.
Optional covers are available to enhance electrical
safety.
Specifications:
Ratings
•
•
•
Volts: 600 V
Amps: 175 to 310 A
SCCR: 200 kA (see table for circuit protection
details)
Flammability rating
•
UL 94 V0
Storage and operating temperature range
•
-4°F to 248°F (-20°C to 120°C)
Agency information
•
•
UL 1953 Listed, Guide QPQS, File E256146
CSA
®
Certified, Class 6228-01, File 47235
Stranded 75°C copper and aluminum
Higher temperature rated conductors permitted
with appropriate derating
Conductors
†
•
•
†
As specified in the catalog number table.
Technical Data 10537
Effective August 2016
UL Listed power distribution blocks
Catalog numbers:
Lineside
Line/load port
configuration
No. of
poles
Current Wire size
rating
(Str/ferrule unless
(A)
noted)*
2/0 - #1 Cu/Al (Str)
#2 - #3 Cu/Al
#4 - #8 Cu/Al
1, 3
175
#10 - #12 Al (Str)
#10 - #14 Cu
#4 - #8 Cu/Al
#10 - #14 Cu
2/0 - #1 Cu/Al (Str)
1, 3
175
#2 - #3 Cu/Al
#4 - #8 Cu/Al
#10 - #14 Cu
2/0 - #1 Cu/Al (Str)
1, 3
175
#2 - #3 Cu/Al
#4 - #8 Cu/Al
#10 - #14 Cu
2/0 - #1 Cu/Al (Str)
#2 - #3 Cu/Al
1, 2, 3
175
#4 - #8 Cu/Al
#10 - #12 Al (Str)
#10 - #14 Cu
350kcmil - 2/0 Cu/Al (Str)
1, 3
310
1/0 Cu/Al (Str)
#1 - #6 Cu/Al
350kcmil - 2/0 Cu/Al (Str)
1, 3
310
1/0 Cu/Al (Str)
#1 - #6 Cu/Al
Wires
per
port
1
1
1
1
1
2
2
1
1
1-2
1-2
1
1
1-2
1-2
1
1
1-2
1
1-2
1
1-2
1-2
1
1-2
1-2
31.1 (275)
†
1
31.1 (275)
†
1
13.6 (120)
1
#4 - #6 Cu/Al (Str)
#8 Al (Str)
#8 Cu
#10 - #12 Al (Str)
#10 - #14 Cu
#4 - #6 Cu/Al (Str)
#8 Al (Str)
#8 Cu
#10 - #12 Al (Str)
#10 - #12 Cu
#10 - #14 Cu
#4 - #6 Cu/Al (Str)
#8 Al (Str)
#8 Cu
#10 - #12 Al (Str)
#10 - #14 Cu
#2 - #3 Cu/Al (Str)
#4 - #8 Al (Str)
350kcmil - 2/0 Cu/Al (Str)
1
#6 - #8 Al (Str)
#4 Cu
#6 Cu
#8 Cu
1, 3
310
1/0 Cu/Al (Str)
1-2
31.1 (275)
†
1
#10 - #12 Cu
#14 Cu
1/0 - #3 Cu/Al (Str)
#4 - #6 Cu/Al
#8 Cu/Al
#1 - #6 Cu/Al
1-2
#10 - #12 Cu
#6 - #14 Cu
#4 - #6 Al (Str)
1
1-2
1
1
1-2
1
1-2
1
1
1
2
1
1-2
1
1
1-2
1
1
2
1
1-2
1-2
1-2
2
1
1
1
1
2
2
5.1 (45)
4.5 (40)
4.0 (35)
5.6 (50)
5.1 (45)
††
4.5 (40)
††
4.0 (35)
††
13.6 (120)
3
200
PDB371-_
6
5.6 (50)
4.0 (35)
2.8 (25)
4.0 (35)
2.3 (20)
4.0 (35)
2.8 (25)
4.0 (35)
2.3 (20)
4.0 (35)
2.8 (25)
4.0 (35)
2.3 (20)
12
200
PDB370-_
6
200
PDB323-_
6
200
PDB321-_
13.6 (120)
1
1/4-20 x 3/4” Stud
—
—
1
200
PDB280-_
13.6 (120)
1
4.0 (35)
13.6 (120)
1
12.4 (110)
††
Loadside
Wire size
Torque
Ports/ (Str/ferrule unless
N•m (Lb-in) pole
noted)*
2/0 - #1 Cu/Al (Str)
#2 - #3 Cu/Al
#4 - #8 Cu/Al
#10 - #12 Al (Str)
#10 - #14 Cu
#4 - #8 Cu/Al
#10 - #14 Cu
#4 - #6 Cu/Al (Str)
#8 Cu
#8 Al (Str)
#10 - #14 Cu
Wires
per
Torque
Ports/
port
N•m (Lb-in) pole
1
1
1
1
1
2
2
1
1
1-2
1-2
4.0 (35)
13.6 (120)
4.0 (35)
2.8 (25)
2.3 (20)
4
200
PDB220-_
1
200
PDB204-_
12.4 (110)
††
Max
SCCR
(kA)**
Catalog
number
* 75°C wire (higher temperature rated wire acceptable with appropriate derating). Using a ferrule on a stranded conductor requires a correctly sized UL Listed ferrule
(customer supplied) applied according to the manufacturer’s specifications. Ferrule ratings apply to copper wire only.
** See pages 4 and 5 for the tested upstream overcurrent protective devices necessary for achieving these SCCRs.
† Torque rating for dual wire and ferrule application is 30.5 N•m (270 Lb-in).
†† Torque rating for ferrule application is 13.6 N•m (120 Lb-in).
2
Eaton.com/bussmannseries
UL Listed power distribution blocks
Technical Data 10537
Effective August 2016
Features and benefits
•
•
High SCCRs up to 200 kA, assist in achieving high SCCR for a
control panel per NEC and UL 508A requirements.
In compliance with UL 1953 minimum spacing requirements for
industrial control panel feeder and branch circuits.
Optional covers available to reduce the risk of accidental contact
with energized components.
Dual wire applications are only viable when using two wires of
the same size, stranding, and insulating and conductor material in
the same port.
Bussmann series PDB power distribution blocks are rated for use
with UL Listed ferrules (see catalog number table for details).
Ferrule applications allow for the use of a broader range of
conductor stranding and simulate a more efficient, solid wire
connection with the PDB terminal port.
Always use UL Listed ferrules in accordance with the
manufacturer’s specifications and instructions.
•
Ferrule terminal application
•
•
•
Dual wire port application
•
Rated for dual wire port application to increase the possible
number of lineside and loadside connections. E.g., PDB220 can
accept two wires into the lineside port (#4 - #14 Cu, #4 - #8 Al)
and two wires per port (eight connections per pole total) on the
loadside lug (#8 - #14 Cu, #8 Al).
•
Selecting SCCR power distribution blocks and terminal blocks
Short-circuit current rated power distribution blocks
Bussmann series power distribution blocks have three distinct
styles to match different application needs. There are the PDBFS_
and PDB_ high short-circuit current rated power distribution blocks
and the 16_ power terminal blocks. The differences are whether the
power distribution blocks are enclosed or not, and whether they are
UL 1953 Listed power distribution blocks or UL 1059 Recognized
power terminal blocks, which have different minimum spacing
requirements. The table on this page will assist you in selecting
which block is right for your application.
(NEC 670.3(A)), and HVAC equipment (NEC 440.4(B)) is required by
the NEC.
Power distribution and terminal blocks not marked with a component
SCCR are typically one of the weakest links in a control panel’s
equipment SCCR and may limit the equipment SCCR to no more
than 10 kA. The PDBFS_ and PDB_ products have the increased
spacing required for use in feeder circuits of equipment listed to
UL 508A (UL 1059 terminal blocks must be evaluated for proper
spacings). Also, for building wiring systems, the PDBFS_ and
PDB_ power distribution blocks can be used to meet the 2014 NEC
requirements in section 376.56(B) for power distribution blocks in
wireways.
See the last page of this data sheet for SCCR tools and resources to
help you further understand and solve your SCCR needs.
Why these are important
Per the NEC and OSHA, equipment cannot be installed in an
electrical system at a location where the available fault (short-circuit)
current is greater than the equipment’s SCCR.
Further, equipment SCCRs are required in the 2014 NEC and for UL
508A Listed control panels. Marking the equipment SCCR on control
Novice sharing, expert detour! I got the AM335X development board this week, and after playing with it for a few days, I can finally display the screen through the Frame Buffer. Share it with everyone...
Does CString have a length limit? When the length is over 1000, CEdit cannot display more content? I want to display the characters in CString on CEdit, but when the length of the read string exceeds ...
The input is a microphone, the output is written to the flash card, and an IP circuit is integrated to remotely manage and download recorded voice files....
According to the sd manual, it should return 0x01, indicating entering the idle state. The highest bit returned by sending CMD0 should always be 0. Why is mine so tragic? Please help:Sad:...
The school laboratory plans to buy some ARM11 development boards. I think the OK6410 is good, but I don't know if the core board is stable or not. What is the structure of the core board?
What are the...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
The above is to use MB1404 as a stereo composite signal transmitter. You can use the internal high-frequency amplifier and oscillator or not! According to my experience, I still recommend beginners...[Details]
Cars equipped with xenon headlights are already common on the road. Whether they are standard equipment on high-end cars or embellishments on modified cars, xenon lamps are gradually becoming a sym...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
