I am very grateful for the opportunity to practice provided by the forum. During the DIY period, I met many good friends, such as Shanshui, Reptile, Maoge, exiao, etc. They have many advantages that a...
First of all, thank you eeworld for giving me this opportunity to test Toshiba's photoelectric relay TLP3547 module. Seeing that other brothers have posted unboxing photos in the forum, I will not pos...
Using the latest IAR and IAR built-in routines, the launchpad driver shows that it is connected, but when downloading the program, it prompts "Fatal error: Failed to re-initialize Session aborted!", a...
I want to ask, can PIC directly determine the status of the pins to scan like 51, for example, using the instruction: btfss portb,6? Or must I use interrupts? There is also this instruction: comf port...
According to the methods of the experts, I changed the CPU type and compiler type selection to PPC85**diab when creating the out file; the previous problem was solved, but the file was still not downl...
1. Principle 1. Infrared emission protocol The infrared transmission protocol has been written in the previous article , so I will not repeat it here. 2. Timer counting and input capture A timer...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
At present, in the world,
the construction of
smart cities
is in the process of gradually landing from concept, and technology giants and investment giants are important participants in this...[Details]
With the development of information technology, intelligence, informatization and networking have become the development trend of modern industrial control. Since the 1980s, the rapid development...[Details]
STM32 has two watchdogs: independent watchdog and window watchdog. This article mainly introduces the use of independent watchdog. Independent watchdog (IDWG): driven by an independent 40KHZ low-sp...[Details]
In mid-to-late 2016, a girl from Hubei came to Beijing alone, full of curiosity about
cloud computing
. The girl left the deepest impression on me was her lovely smile. She told me that if ...[Details]
Introduction: As a power electronic device, the photovoltaic inverter mainly converts the direct current generated by the photovoltaic module into alternating current. Because there are thousands o...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Design a program for the 51 single-chip microcomputer. It is known that the crystal oscillator frequency of the 89C51 single-chip microcomputer is 12MHz, and it is required to use T1 timing to output...[Details]
Try to design a subroutine, whose function is to rearrange the 6 single-byte positive integers in the internal RAM pointed to by (R0) in ascending order. ;========================================== ...[Details]
It is required to use MCS-51 microcontroller to sort data. 1. Sort the 8 data in ascending order; 2. The data to be sorted is stored in the internal data memory address units 30H-37H, which are 34H, ...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
