Note: A 0.01 Ohm addition to be added to the performance of all resistors <10 Ohms.
Pulse Performance Data
Lightning Surge
Lightning surge resistors are tested in accordance with IEC 60 115-1 using both 1.2/50µs and 10/700µs pulse shapes. 10 pulses are applied. The limit of
acceptance is a shift in resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
The single impulse graph is the result of 50 impulses of rectangular shape applied at one minute intervals. The limit of acceptance was a shift in
resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Continuous Load Due to Repetitive Pulses
The continuous load graph was obtained by applying repetitive rectangular pulses where the pulse period was adjusted so that the average
power dissipated in the resistor was equal to its rated power at 70°C. Again the limit of acceptance was a shift in resistance of less than 1% from the
initial value
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
[font=微软雅黑][size=4]Recently, various great activities have emerged in EEWORLD:pleased:such as: [/size][/font][font=微软雅黑][size=4][color=red][url=https://www.eeworld.com.cn/huodong/201310_TI_SensorTag/]...
As a hard-working coder, I don’t have any time for myself during the day, so I have to reduce my sleep....I made an interface imitating Win7 calculator. Here are the pictures first. I haven't done the...
There is strength in numbers. Thanks to everyone's efforts, our first step - the Getting Started section - has been basically completed and organized into a post for your reference:Written at the begi...
As shown in the figure above, in the spi interface of AD7193, the corresponding ground plane is DGND. When using ADUm5401 for isolation, the ground on the left side of ADUM5401 is connected to DGND, a...
When burning the program with an emulator, some of the 28335's gpio levels are high and some are low. Can someone please tell me whether this is due to random pins during burning or which gpio pins ar...
[i=s]This post was last edited by ddllxxrr on 2014-12-31 09:39[/i] The following is to test the wireless transmission of the two modules. The previous post was about serial port transparent transmissi...
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Car lights, whether headlights, fog lights or tail lights, play an important role in driving safety. However, the material of the car lights determines that the probability of damage in a collision...[Details]
At present,
the control system used in
automobiles
can be divided into three parts from the functional point of view:
sensor
unit, control unit and execution unit. Among them,
th...[Details]
The number of timers/counters and interrupt sources directly determines the performance of the microcontroller. The MCS-51 microcontroller has two programmable 16-bit timers/counters and five inter...[Details]
For a long time, my country has implemented "community-style collective heating" for hot water heating, and settled accounts based on the heating area, regardless of whether the user uses heat. Thi...[Details]
Current sensing in automotive applications includes controlling the current through solenoids and injectors. For example, during diesel injection, we rapidly increase the current to the induction i...[Details]
Many industrial fields such as industrial automation, logistics, and smart grids require that machinery and products be safe and have passed functional safety certification. When developing machine...[Details]
Background
The proliferation of ultra-low-power wireless sensor nodes for measurement and control purposes, combined with new energy harvesting techniques, has made it possible to create ful...[Details]
The coking workshop of Tianjin No. 2 Gas Plant is the core of the whole plant's production and an important source of economic and social benefits. Its production automation level and management an...[Details]
1. Introduction
Industrial fieldbus technology is one of the technologies that has received the most attention in the automation industry in recent years, and it has brought a qualitative leap...[Details]
1. Composition of product standard system
LED is a new type of lighting appliance product. LED products include the LED itself, the supporting control devices and the lighting products that us...[Details]
Typically, buck regulators are designed for continuous mode operation, which simplifies output voltage calculations and system design. However, if the system is non-synchronous and required to oper...[Details]
Suggestions & Announcements
京公网安备 11010802033920号
EEWORLD
