EEWORLDEEWORLDEEWORLD

Part Number

Search

R0202AS-02-9761-C

Description
Fixed Resistor, Thin Film, 0.25W, 9760ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

R0202AS-02-9761-C Overview

Fixed Resistor, Thin Film, 0.25W, 9760ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP

R0202AS-02-9761-C Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1579459877
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
JESD-609 codee3
Manufacturer's serial numberWBC
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance9760 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeONE SURFACE
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Tell me how you got to work today?
The snow in the morning was 20cm thick, I guess~~ I arrived at the bus stop around 6:30. There were two cars parked there, and I was driven to another car by the driver of one car. I slept drowsily on...
soso Talking
How does PN532 Soft Power down work?
Looking at the official information of pn532, it mentions Soft Power down, and the power consumption is only 25ua, but I don’t know how to operate it. Please give me some advice if you have experience...
nzmnyqlxz RF/Wirelessly
Haha, this is my first time making a microcontroller learning board. I'm showing it off.
Haha, this is my first time to make a single-chip learning board, using AVR chips. ATmega16 single-chip learning board. The learning board always needs a name. After thinking about it, I couldn't thin...
tiankai001 MCU
Test Technology of Analog Integrated Circuits
With the advancement of integrated circuit manufacturing technology, people have been able to manufacture integrated circuits with complex circuit structures, high integration, and various functions. ...
fighting Test/Measurement
How is the touch effect of STM8?
I would like to ask those who have used STM8 for touch. I heard from some friends that the library provided by ST has many bugs and is not convenient for debugging. Is this true? Thank you! Recently, ...
zyyu stm32/stm8
About the display problem under UCOS+UCGUI
Experts, I transplanted a 2.4 screen program to a 3.2 screen under UCOS+UCGUI, but found that only a part of it is displayed on the 3.2 screen, and the position of the finger on the touch screen and t...
112233ab stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 301  2370  1286  2489  183  7  48  26  51  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号