Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Phenomenon: 1. Normal startup. If the USB sync cable is inserted at this time, the connection is normal; but if it is hibernated at this time, it freezes after waking up. 2. Normal startup. If it is h...
Emergency help: LMK03806B can output normally sometimes, but not normally? LMK03806 chip is configured by Xilinx K7 FPGA, and the circuit reference manual is used. However, the input part does not hav...
I would like to ask you a question: [color=#FF0000]Conditions:[/color] Run the WinCE Test Kit tool (cetest.exe) on the PC, connect to the target device through ActiveSync and detect the driver module ...
I downloaded a spi driver source code compiled in wince6.0 environment. Can I directly add it to wince 5.0 platform for operation? In addition, after I compiled it with the driver on wince5.0 platform...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility?
1. The following systems should pay special attention to anti-...[Details]
In the TV monitoring system, in order to complete the collection of information from various information points (video, audio, alarm signal) and the control of various front-end devices (PTZ, lens,...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
0 Introduction
Pneumatic
artificial muscle,
also known as pneumatic muscle actuator (PMA), began to be studied in the 1950s. In recent years, it has been widely studied and applied ...[Details]
AUTOSAR is a hierarchical architecture for automotive electronic embedded software jointly launched by global automotive OEMs and suppliers. The hierarchical architecture consists of a microcontrol...[Details]
1. Low temperature storage
Lithium-ion power batteries need to be fully charged before storage. They can be stored at 20°C for more than half a year, which shows that lithium-ion power batteri...[Details]
With the development of power electronics technology and high-performance permanent magnet materials, the application of brushless DC motors has achieved rapid development in the fields of aerospace, ...[Details]
The Challenge:
Improving Siemens Wind
Turbine Controls
System software automated testing for regular releases, validating wind turbine control system components during the developme...[Details]
As the electromagnetic environment in space becomes increasingly complex, the shielded cables used to transmit weak signals in the test system are easily affected by external electromagnetic distur...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
