EEWORLDEEWORLDEEWORLD

Part Number

Search

240-383EH221-41SPCANN

Description
MIL Series Connector, 41 Contact(s), Stainless Steel, Female, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size391KB,2 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

240-383EH221-41SPCANN Overview

MIL Series Connector, 41 Contact(s), Stainless Steel, Female, Solder Terminal, Receptacle

240-383EH221-41SPCANN Parametric

Parameter NameAttribute value
Reach Compliance Codecompli
Other featuresSTANDARD: MIL-DTL-38999; POLARIZED
Back shell typeSOLID
Body/casing typeRECEPTACLE
Connector typeMIL SERIES CONNECTOR
Contact to complete cooperationGOLD (50) OVER NICKEL
Contact completed and terminatedGOLD (50) OVER NICKEL
Contact point genderFEMALE
Coupling typeTHREADED
DIN complianceNO
empty shellNO
Environmental characteristicsCORROSION/ENVIRONMENT/FLUID/IMMERSION/VIBRATION RESISTANT
Filter functionYES
IEC complianceNO
JESD-609 codee4
MIL complianceYES
Manufacturer's serial number240-383E
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeBOARD AND PANEL
OptionsHERMETIC
Shell surfaceNICKEL PLATED
Shell materialSTAINLESS STEEL
Housing size21
Termination typeSOLDER
Total number of contacts41
Base Number Matches1
240-383E
MIL-DTL-38999 Series III Filter Connector
Dual Flange Jam Nut Receptacle
Contact Gender
P
- Pin
S
- Socket
C
.835/.825
(21.2/21.0)
.130/.120 (3.3/3.0)
.131/.125 (3.3/3.2)
Master
Keyway
.675/.671 (17.1/17.0)
.172/.132
(4.4/3.4)
U
(see Table IV)
Radius H
4 Places
10
16
28
33
37
34
29
23
16
23
28
29
33
34
37
10
EMI/EMP
Filters
MIL-DTL-38999 Series III
Filter Connector
Product Code
Alternate Key Position
Per MIL-DTL-38999
A, B, C, D, E, N = Normal
Insert Arrangement
IAW MIL-STD-1560
Filter Type
P
- Pi Circuit
C
- C Circuit
Capacitance
(See Table II)
240
-
383
E
P
15-35
P
P
P
A
N
N
Shell Style
E
- Dual Flange Jam Nut
Connector Class
(See Table I)
Termination
P
- PC Tail
Flange Mounting Style
N
- Not Applicable
E
- Dual Flange Jam Nut
F
2 Places
P
4 Places
Interrupted
K Dia
1
5
4
9
15
22
.510 (13.0)
Max Red Band
Full Mate Indicator
4
9
15
22
1
5
D
Flat
Interrupted
L Dia
See
Note 3
Thread B
N (4 Places)
45° 4 Places
.100 (2.5)
.110
(2.8)
.250 (6.4)
Interrupted J Dia
ØE
Thread R
J Flat
4-40 Helicoils
Installed per NASM 33537
Tang Removed
TABLE IV:
PC TAIL DIAMETER
Contact
Size
22D
20
Ø
U
.018/.021
(0.5/0.5)
.029/.031
(0.7/0.8)
.038/.042
(1.0/1.1)
H
16
© 2008 Glenair, Inc.
www.glenair.com
CAGE CODE 06324
Printed in U.S.A.
E-Mail: sales@glenair.com
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
C-32
Check out the new post function, everyone take a look~~~
Previously, Blue Eye Fox and wangjiafu1985 suggested that the forum should have a function to view new posts. This function was added today:As shown in the figure: Label 1 remains the same, including ...
soso Suggestions & Announcements
Winding inductance of electrolytic capacitor
The electrolytic capacitor is made of two strips of aluminum foil with insulating paper. Because it is wound, it is considered to be an inductor. This conclusion has been circulated for decades. I don...
PowerAnts Analog electronics
As a beginner, how can I learn the relevant knowledge of WINCE?
Since I will be going to the company for internship in two months, the engineer from the relevant department of the company informed me that I should first familiarize myself with the wince system and...
t63056 Embedded System
How does COMBOBOX get focus?
I want to do something when COMBOBOX gets the focus. The method I used is if(GetFoucs()->GetDlgCtrlID==IDC_XXX), but the cursor is clearly on COMBOBOX but it doesn't seem to get the focus. The same co...
2002xiao Embedded System
I have some questions about a small program and need some advice
module count4(out,reset,clk); output[3:0] out; input[3:0] reset,clk; reg[3:0] out; always @(posedge clk)beginif(reset) out=0;else out=out+1;end endmoduleIs the reason why out is defined as a register ...
leomeng FPGA/CPLD
2440, bootloader problem
My bsp contains stepldr and eboot, I want to run eboot, but after burning stepldr.nb1 into flash, dnw shows garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Init(void) ...
ricky03221115 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2798  1817  1370  1140  1301  57  37  28  23  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号