EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

RPC0805DT2K20

Description
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 2200ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
CategoryPassive components    The resistor   
File Size783KB,12 Pages
ManufacturerSEI(Stackpole Electronics Inc.)
Websitehttps://www.seielect.com/
Environmental Compliance
Download Datasheet Parametric View All

RPC0805DT2K20 Overview

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 2200ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP

RPC0805DT2K20 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid274665162
package instructionCHIP
Reach Compliance Codecompliant
Country Of OriginTaiwan
ECCN codeEAR99
YTEOL8.2
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length2 mm
Package formSMT
Package width1.25 mm
method of packingTR, PAPER, 7 INCH
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance2200 Ω
Resistor typeFIXED RESISTOR
size code0805
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage150 V
STM32 external expansion SRAM reading data problem
My sram is is61lv25616al 256k. The data width I store is 8bit. When reading the data, I found a problem. It repeats 7 times with more than 4000 data as a unit and then reads the next one... I have bee...
雨夏 stm32/stm8
[MSP430 Sharing] Design of Infusion Monitoring System Based on Fuzzy Neural Network
With MSP430 MCU as the control core, combined with infusion sensor, electric actuator, LCD display, keyboard, etc., automatic monitoring of the infusion process is realized. Since the infusion system ...
鑫海宝贝 Microcontroller MCU
Is there anything I need to pay attention to when using P3_7 as a normal pin?
Why is this pin always 0 when I use the emulator to simulate the microcontroller?...
j1a2s3o4n 51mcu
I soldered a 51 board, and all pins except the GND pin are high level. Please help
The program has been tested on other boards and there is no problem. The pins are all connected. Now I am wondering if it is a problem with the crystal oscillator circuit or the reset circuit? The cry...
timfay 51mcu
Modelsim simulation encountered problems
When simulating with modelsim, it prompts error loading design. How to solve it?...
爱风流 FPGA/CPLD
IBM mobile hard disk problem~! (urgent)
Hello everyone, I have an IBM mobile hard disk, which was working fine yesterday. When I plugged it into the computer, I found 3 EXE files, so I deleted them casually. I also deleted the Recycled in t...
jkwzh Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2296  563  284  854  25  47  12  6  18  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号