EEWORLDEEWORLDEEWORLD

Part Number

Search

D24A000T17302ETB-G

Description
Parallel - 3Rd Overtone Quartz Crystal, 24MHz Nom, HC-49/U, 3 PIN
CategoryPassive components    Crystal/resonator   
File Size698KB,3 Pages
ManufacturerDB Lectro Inc
Environmental Compliance  
Download Datasheet Parametric View All

D24A000T17302ETB-G Overview

Parallel - 3Rd Overtone Quartz Crystal, 24MHz Nom, HC-49/U, 3 PIN

D24A000T17302ETB-G Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1390481648
package instructionHC-49/U, 3 PIN
Reach Compliance Codeunknown
Other featuresBULK
Ageing3 PPM/YEAR
Crystal/Resonator TypePARALLEL - 3RD OVERTONE
Drive level100 µW
frequency stability0.002%
frequency tolerance30 ppm
load capacitance17 pF
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency24 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
physical sizeL11.05XB4.65XH13.46 (mm)/L0.435XB0.183XH0.53 (inch)
Series resistance50 Ω
surface mountNO
QUARTZ CRYSTAL
Holder Code A, RESISTANCE WELDED HC-49/U PACKAGE
FEATURE
Height 13.46mm
A resistance weld completely sealed type
The tight frequency stability
Copes with high density mounting and is the optimum for
mass production
Lead Free & RoHS Compliant
ELECTRICAL SPECIFICATIONS
Nominal frequency:
Oscillation mode:
Operating temperature range
Storage temperature range
Frequency tolerance:
Frequency stability
Load capacitance:
Equivalent series resistance
Parallel capacitance(Co):
Drive level
Insulation resistance:
1.8432MHz to 150.000MHz
See below table
-20℃--+70℃ (Typical), -10℃ ~ +60℃,
-40℃ ~ +85℃, or specify
-40℃--+85℃
±30PPM
at 25±2℃ (Typical), or specify
±50PPM
over -20~70℃ (Typical), or specify
16pF, 18pF, 20pF, 30pF, series, or specify
See below table
7PF Max
100 µW Typical
More than 500MΩ AT DC100V
EQUIVALENT SERIES RESISTANCE(ESR) AND OSCILLATION MODE
Frequency Range
1.843MHz~1.999MHz
2.000MHz~2.399MHz
2.400MHz~2.999MHz
3.000MHz~3.199MHz
3.200MHz~3.499M
Hz
3.500MHz~3.899MHz
3.900MHz~4.099MHz
4.100MHz~5.999MHz
E.S.R
(
Ω)
350Max
300Max
200Max
150Max
100Max
90Max
70Max
60Max
Mode
Fundamental/AT
Fundamental/AT
Fundamental/AT
Fundamental/AT
Fundamental/AT
Fundamental/AT
Fundamental/AT
Fundamental/AT
Frequency Range
6.000MHz~6.999MHz
7.000MHz~9.999MHz
10.000MHz~12.999MHz
13.000MHz~30.000MHz
24.000MHz~29.999MHz
30.000MHz~65.000MHz
60.000MHz~99.999MHz
100.000MHz~150.000MH
z
E.S.R
(
Ω)
50Max
30Max
20Max
20Max
50Max
40Max
90Max
60Max
Mode
Fundamental/
AT
Fundamental/
AT
Fundamental/
AT
Fundamental/
AT
Third
Overtone
Third
Overtone
Third
Overtone
Fundamental/
AT
DB Lectro Inc. 3755 Place Java, Suite 140, Brossard, Québec, J4Y 0E4, Canada - T: 1-450-444-1424 / F: 1-450-444-4714 / www.dblectro.com
51 MCU Elf, it is said that you can program even if you don't know MCU
[i=s] This post was last edited by paulhyde on 2014-9-15 09:05 [/i] 51 MCU Wizard, it is said that even if you don't know MCU, you can still program. In fact, it is a collection of small tools. I took...
open82977352 Electronics Design Contest
Question: The handset of a telephone is 130 ohms. I have set up a telephone board. How can I modify the headphone circuit so that I can use 30 ohm headphones?
The phone chip used is TEA1062, SPK is connected to the headset through capacitor C; there is a resistor R between SPK and GAR. The test found that: when R = 100K, C = 1UF, the quality of the telephon...
zfnlj Embedded System
pwm brushless ESC N5065 motor
I bought an fvt brushless ESC, an N5065 motor, and used the PWM driver of STM32. Set the throttle range according to the instructions: ****************************************** First turn off the ESC...
liuw2010 Electronics Design Contest
Problems with converting VHDL integer to real
I want to convert integer type signal to real type. The program is as follows. This program reports an error in maxplus II: file standard.vhdl:Unsupported feature error:floating is not supported An er...
力量 Embedded System
XILINX EDK: Get data from the serial port
Hello everyone! I'm learning Xilinx EDK recently, and I'd like to ask you a question. First of all, the board I'm using is ML506, and the software is EDK 11.1. There is a "hello world" program in the ...
applelonger FPGA/CPLD
Breakpoint setting in CCS3.3
1. If breakpoints cannot be set during simulation under CCS3.3. You need to check your project configuration. Open Build Optins, and in Basic under the Complier dialog box, set Generate Debug to Full ...
ltbytyn Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2752  442  884  766  1310  56  9  18  16  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号