2. Metric equivalents are given for general information only.
3. Unless otherwise specified, tolerances are ±0.010 inch (0.25 mm).
4. Lead frame configuration is shown as typical above the seating plane. The seating plane shall be configured to create a standoff height of 0.055 inch
±0.010 inch when the part is mounted to a printed circuit board (PCB). The standoff height shall be the distance between the PCB and the bottom of
the chip stack. A seating plane is only required for lead style N.
5. See Table 1 for specific maximum A dimension. For maximum B dimension, add .065 inch (1.65 mm) to the appropriate A dimension. For all lead
styles, the number of chips is determined by the capacitance and voltage rating.
6. For case code 5, dimensions shall be .100 inch (2.54 mm) maximum and 0.012 inch (0.30 mm) minimum.
7. Lead alignment within pin rows shall be within ±0.005 inch (0.13 mm). Lead alignment between pin rows shall be within one half of the lead width
(0.010 inch (0.25 mm)).
Lead Configurations – Inches (Millimeters)
Lead Style
Symbol
N
L
J
Lead Style
(N) Straight
(L) Formed
(J) Formed
L
Lead Length
0.250 Minimum (6.35)
0.070 ±0.010 (1.78 ±0.25)
0.070 ±0.010 (1.78 ±0.25)
Additional lead configurations may be available. Contact KEMET for details.
I would like to ask: When the DSP2812 program is burned into FLASH and runs, what is the highest stable clock frequency? There are also some opinions about 100M and 120M. Please give me some advice....
Please recommend some good books about Linux drivers and kernel, thank you~! The more classic the better. Please also recommend some books about Wince, thank you~!...
I am new to embedded systems. I have a 2410 development board with a BSP for wince4.2. I want to use it in 5.0, but my ability is limited. I put the files in 5.0 and removed the previous 2410.cec and ...
[flash]http://player.youku.com/player.php/sid/XMTQxNzY2MDUy/v.swf[/flash] This is the future: Without a watch, your arm is the watch; without a camera, your hands are the camera; without a screen, a p...
Hot discussion: How many spacings are required for GND vias in RF high-speed PCB design?Jianghu boy said: It is for better grounding and to prevent interferenceWhite-robed swordsman says: The "fence" ...
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
Based on the commutation technology, thyristor rectifiers are classified into two main types. Line-commutated and force-commutated inverters are commonly used, while other commutated inverters, nam...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
A pure sine wave inverter has a good output waveform with very low distortion, and its output waveform is essentially the same as the AC waveform of the mains power grid. In fact, the AC power prov...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
On August 18th, China's largest expressway
charging station,
the G25 Changshen Expressway Tonglu Service Area (South Area), officially opened and launched its integrated solar-storage-charg...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
introduction
In recent years, with the increasing number of high-rise buildings, the demand for elevators has also increased. Currently, the elevators we use most often use LED dot array displ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
