UTC LM8560
DIGITAL ALARM CLOCK
DESCRIPTION
The LM8560 is alarm equipped digital clock IC with built-in
driver capable of directly driving LED display equipment. As IC
himself the VDD pin for the LM8560 is graded to withstand a
voltage of 15V.
MOS IC
FEATURES
*Single chip P-channel ED MOS LSI
*LED direct drive using time division (duplex configuration)
*Wide operating power supply voltage range
*Built-in alarm function with 24-hour control
*Supports changeover between 12-hour AM/PM and 24-hour
displays
*Built-in battery backup CR oscillator
*Users 50Hz or 60Hz as standard frequency
*Built-in automatic fast forward function for hour and minute
settings
*Built-in sleep timer function (maximum intervals of 59 minutes
or 1 hours and 59 minutes)
*Built-in snooze function supporting repeat use
*Equipped with power failure display function
*900Hz output for alarm tone
SDIP-28
FUNCTIONS
*Current time display
*Snooze alarm function
*Sleep timer function (maximum intervals of 59 minutes or 1
hours and 59 minutes)
APPLICATIONS
*Alarm clocks
*Clock radios
UTC
UNISONIC TECHNOLOGIES CO., LTD.
1
QW-R502-005,D
UTC LM8560
PIN CONFIGURATIONS
AM& 10'S HR
ag&de
PM& 10'S HR b
10'S HR c& HR e
HR b&g
HR c&d
HR a&f
10'S MIN a&f
MOS IC
1
2
3
4
5
6
7
28
27
26
12/24 HR Select
CR Input
50/60 Hz Select
25 50/60 Hz Input
24 Snooze Input
23
Sleep Display
LM8560
22 Hour Set
21
20
19
18
Minute Set
VDD
Alarm Display
Alarm OFF
10'S MIN b&g 8
10'S MIN c&d 9
10'S MIN e &Min e 10
MIN b&g 11
MIN c&d 12
MIN a&f 13
Colon Output 14
17 Sleep Output
16
15
Alarm Output
VSS
ABSOLUTE MAXIMUM RATINGS
(Ta=25°C, Vss=0V)
PARAMETER
Maximum Supply Voltage
Input Voltage1
Input Voltage2
Output Voltage
Input Clamp Current
Allowable Power Dissipation
Operating Temperature
Storage Temperature
SYMBOL
V
DD (max)
V
IN
1
V
IN
2
V
OUT
l
IN
P
D (max)
Topr
Tstg
TEST CONDITIONS
50/60Hz Input
Except 50/60Hz Input
50/60Hz Input
Ta=70°C
RATING
-15~ +0.3
-15~ +0.3
-15~ +0.3
-15~ +0.3
-0.4 ~+0.4
700
-30 ~ +70
-55 ~ +125
UNIT
V
V
V
V
mA
mW
°C
°C
ALLOWABLE OPERATING RANGES
(Ta=25°C, Vss=0V )
PARAMETER
Supply Voltage
Input “H” Level Voltage1
Input “L” Level Voltage1
Input “H” Level Voltage2
Input “L” Level Voltage2
50/60Hz Input Pin Input
Voltage
SYMBOL
V
DD
V
IH
1
V
IL
1
V
IH
2
V
IL
2
V
AC-IN
TEST CONDITIONS
50/60Hz Input
50/60Hz Input
Except 50/60Hz Input
Except 50/60Hz Input
Sets V
SS
as Reference
MIN.
-14
-1
-1.5
TYP.
MAX.
-7.5
V
DD
+2
V
DD
+2
UNIT
V
V
V
V
V
V
V
LED
UTC
UNISONIC TECHNOLOGIES CO., LTD.
2
QW-R502-005,D
UTC LM8560
PARAMETER
Input “H” Level Current 1
Input “L” Level Current 1
Input “H” Level Current 2
Input “L” Level Current 2
Output “H” Level Current 1
Output Leakage Current 1
Output “H” Level Current 2
Output Leakage Current 2
Output “H” Level Current 3
Output Leakage Current 3
Power failure detection
Voltage
Consumption Current
Backup Oscillator Stability
Factor
Backup Oscillator
Accuracy
MOS IC
SYMBOL
I
IH
1
I
IL
1
I
IH
2
I
IL
2
I
OH
1
I
OF
1
I
OH
2
I
OF
2
I
OH
3
I
OF
3
V
DD
I
CC
F
S
F
A
Output set to off and Pull-down attached
input set open
Standard Value,900Hz,
V
DD
=-9V±10%-10
Standard Value,900Hz, V
DD
=-9V-10
ELECTRICAL CHARACTERISTICS
(Ta=25°C, V
DD
=-12V unless otherwise specified)
TEST CONDITIONS
50/60Hz Input, V
IN=
V
SS
50/60Hz Input, V
IN=
V
DD
Input Pins Other Than 50/60Hz Input
V
IN=
V
SS
Input Pins Other Than 50/60Hz Input
V
IN=
V
DD
Alarm Output and Sleep Output
V
OH
=V
SS
-1V
Alarm Output and Sleep Output
V
OUT
=V
DD
AM & 10’S HR ag & de (24H mode)
V
OUT
=V
DD-
1V
AM & 10’S HR ag & de (24H mode)
V
OUT
=V
DD
Segment Output Other Than Those
V
OUT
=V
SS
-1V
Segment Output Other Than Those
Listed Above, V
OUT
=V
DD
MIN.
TYP.
MAX.
10
10
20
10
UNIT
µA
µA
µA
µA
mA
5
10
36
20
18
20
-7.5
-5
5
-10
-10
7
10
10
µA
mA
µA
mA
µA
V
mA
%
%
DESCRIPTION OF OPERATIONS
*50/60Hz Input:
Built-in Shumidt circuit enables noise eliminations at 50/60Hz commercial frequencies with use of a
simple CR filter. Built-in pull-up resistor.
*CR Input:
When the AC power supply is interrupted, the time counter switches to a holding state and a built-in
oscillator promptly begins operation. If 50/60Hz input continues for 3 clocks without arriving, this
oscillator’s output is activated and functions as the time counter clock in place of 50/60Hz input. The
frequency level of this clock oscillator is determined according to the CR value. While the above
mentioned oscillator is operating using backup mode, all segment output is switched to OFF.
(Note) When the backup oscillator is in use due to an AC power supply interruption, the 50/60Hz input
pin must be maintained open or at a V
SS
level.
*50/60 Selective Input:
When 50/60 selective input is connected to V
SS
, 50Hz use is enabled. When 50/60 selective input is
left open, VDD is activated using an internal pull-down resistor and the setting is switched to enable use
at 60Hz.
*Display Mode Selective Input (Alarm Select/Sleep Select):
Since the pull-down resistor is built-in , selection from four display modes is possible using two SPST
switches (single-pole and single-throw switches). Table 1 shows these display mode selections.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
3
QW-R502-005,D
UTC LM8560
Table1 Display Modes
Selective lnput
Alarm
Sleep
NC
NC
Display Mode
Time display
Digit No. 1
10’s place for
hour, AM/PM
10’s place for
hour, AM/PM
Digit No. 2
Hour
MOS IC
Digit No. 3
Digit No.4
10’s place for
Minute
Minute
10’s place for
V
SS
NC
Alarm display
Hour
Minute
Minute
10’s place for
NC
V
SS
Sleep display
Clear
Hour
Minute
Minute
10”s place for
V
SS
V
SS
Second display
Clear
Minute
Second
Second
Note: Activating V
SS
using two inputs simultaneously (alarm select and sleep select), the display mode is switched to
display seconds.
*Time Setting Input:
There are two setting inputs for use with “hour” and “minute”. Time content settings show in Table2 are
possible by activating V
SS
to these pins, A pull-down resistor is built-in.
Table2 Setting contents
Functions
Immediately adds 1 to hour digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Min
Immediately adds 1 to minute digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second. Seconds are rest.
Both
Operates both as outline above.
Second
Hour (note1)
Second digits are cleared to [00].
(Alarm & Sleep)
Min
Time holds.
Both (note2)
Resets hour and minute digits as [0:00] when operating in 24-H mode or
[12:00] when operating in 12-H mode.
Alarm
Hour
Immediately adds 1 to hour digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Min
Immediately adds 1 to minute digits and then assigns an additional 1, at a
speed of 2 Hz, after each 1/4 to 3/4 second.
Both
Resets hour and minute digits as [0:00] when operating in 24-hour mode or
[12:00] when operating in 12-hour mode.
Sleep
-
Sets sleep counter to [0:59] instantly when V
DD
is activated to sleep select
Hour
Sets Sleep counter to [1:59] instantly when V
DD
is activated to sleep select
and hour at the same time.
Min
Sleep counter looses 1 at a speed of 2 Hz.
Both
Sleep counter looses 1 at a speed of 2 Hz.
Note:1.Once conditions have been switched to reset or hold, input of other functions is locked until both Hour and
Min input have been separated.
2.When the digital reading for seconds is between 30 and 59 seconds, 1 is added to the digits for minutes as
he digital reading for seconds rests to [00].
*12/24H Select Input :
When this pin set open (V
DD
), a 12-hour display is enabled whereas connecting this pin to V
SS
enables
the 24-hour display. A pull-down resistor is build-in.
*Power Failure Detection Display :
Display Mode
Time
Set Input
Hour
UTC
UNISONIC TECHNOLOGIES CO., LTD.
4
QW-R502-005,D
UTC LM8560
MOS IC
When activated by drop in power supply, all segments which are lit begin to blink and the unit switches
to a power failure detection display. The power failure detection display is canceled by activating V
SS
to
Hours set or Min set.
*Alarm Operation and Alarm Output :
The alarm signal outputs when alarm content matches the content of current time. When not rest by
either snooze input or alarm off input, output continues after 1 hour and 59 minutes. This output signal
consists of 900Hz 2Hz intermittent (50% duty) modulation signals, When the need arises , a filter can be
applied to after the alarm signal to a DC signal.
*Snooze Input :
When the alarm is sounding and instantly activating V
SS
to this pin , alarm output is set to OFF for a
period between 8 and 9 minutes after which time the alarm signal is once again output. The snooze
function can be used repeatedly in 1 hours and 59 minutes intervals. A pull-down resistor is built-in
Activating V
SS
to the snooze pin when the alarm is OFF resets the sleep timer counter to [0:00 ](This is
known as the one-touch sleep timer reset function.)
*Alarm Off Input :
Activating this input pin to VSS instantly sets alarm output to OFF.A pull-down resistor is built-in.
*Sleep Timer and Sleep Output :
Sleep output can turn on the radio and can be set for time intervals of 59 minutes or 1 hour and 59
minute. Refer to Table 2 for the proper selection procedure (59 minutes or 1 hour and 59 minute
selection.) This sleep timer is constructed using a down counter and when the counter content arrives at
[00], output is set to off and the radio turns off. Adding V
SS
to snooze input turns sleep output off. When
sleep output is on.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
5
QW-R502-005,D
京公网安备 11010802033920号
EEWORLD
