XC6102D430 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > XC6102D430

Preview

XC6102D430: DescriptionCMOS Voltage Detector; File Size519KB，26 Pages; Manufacturer

Download Datasheet View All

XC6102D430 Overview

CMOS Voltage Detector

Preview

Download Datasheet

View All

Preliminary

◆CMOS

Voltage Detector

◆Manual

Reset Input

◆Watchdog

Functions

◆Built-in

Delay Circuit

◆Detect

Voltage Range: 1.6~5.0V, ± 2%

◆Reset

Function is Selectable

DFL

(Low When Detected)

DFH

(High When Detected)

■APPLICATIONS

●Microprocessor

reset circuits

●Memory

battery backup circuits

●System

power-on reset circuits

●Power

failure detection

■GENERAL

DESCRIPTION

■FEATURES

Detect Voltage Range

Hysteresis Range

: 1.6V ~ 5.0V, +2%

(100mV increments)

: V

x 5%, TYP.

(XC6101~XC6107)

x 0.1%, TYP.

(XC6111~XC6117)

: 1.0V ~ 6.0V

The XC6101~XC6107, XC6111~XC6117 series are

groups of high-precision, low current consumption voltage

detectors with manual reset input function and watchdog

functions incorporating CMOS process technology. The

series consist of a reference voltage source, delay circuit,

comparator, and output driver.

With the built-in delay circuit, the XC6101 ~ XC6107,

XC6111 ~ XC6117 series’ ICs do not require any external

components to output signals with release delay time.

Moreover, with the manual reset function, reset can be

asserted at any time. The ICs produce two types of

output; V

DFL

(low when detected) and V

DFH

(high when

detected).

With the XC6101 ~ XC6105, XC6111 ~ XC6115 series’

ICs, the WD pin can be left open if the watchdog function

is not used.

Whenever the watchdog pin is opened, the internal

counter clears before the watchdog timeout occurs.

Since the manual reset pin is internally pulled up to the V

pin voltage level, the ICs can be used with the manual

reset pin left unconnected if the pin is unused.

The detect voltages are internally fixed 1.6V ~ 5.0V in

increments of 100mV, using laser trimming technology.

Six watchdog timeout period settings are available in a

range from 6.25msec to 1.6sec.

Seven release delay time 1 are available in a range from

3.13msec to 1.6sec.

Operating Voltage Range

Detect Voltage Temperature

Characteristics

: +100ppm/

C (TYP.)

Output Configuration

: N-channel open drain,

CMOS

Watchdog Pin

: Watchdog input

If watchdog input maintains

‘H’ or ‘L’ within the watchdog

timeout period, a reset signal

is output to the RESET

output pin

Manual Reset Pin

: When driven ‘H’ to ‘L’ level

signal, the MRB pin voltage

asserts forced reset on the

output pin.

Release Delay Time

: 1.6sec, 400msec, 200msec,

100msec, 50msec, 25msec,

3.13msec (TYP.) can be

selectable.

Watchdog Timeout Period

: 1.6sec, 400msec, 200msec,

100msec, 50msec,

6.25msec (TYP.) can be

selectable.

■TYPICAL

APPLICATION CIRCUIT

■TYPICAL

PERFORMANCE

CHARACTERISTICS

●Supply

Current vs. Input Voltage

XC61X1~XC61X5 (2.7V)

Supply Current:

ISS (µA)

Input Voltage:

VIN (V)

Ta=-40

℃

Ta=25

℃

Ta=85

℃

* Not necessary with CMOS output products.

* ‘x’ represents both ‘0’ and ‘1’. (ex. XC61x1⇒XC6101 and XC6111)

XC6101_07_XC6111_17 ETR0207_009

1/26

Recommended Resources

base amplitude modulation circuit

High-voltage additional circuit of a high-low voltage composite circuit boosted by a transformer

Temperature automatic controller circuit

FOTILE FYB-T2 intelligent hot and cold water dispenser circuit diagram

Sampling and holding circuit diagram using LF398H

Pest control circuit diagram_Electronic mosquito repellent circuit diagram

【Mobile Phone DIY】Xin Xin 8: Don’t say anything, at least send the message: [i=s] This post was last edited by Xin Xin on 2014-11-14 00:46 [/i] [b][size=4] First, let me talk about the current situation: Referring to the manual of SIM900A, I finally succeeded in sending SMS i...; 辛昕 DIY/Open Source Hardware

What simulation software is generally used when making switching power supplies?: There are many common simulation software, but for switching power supplies, because of the higher requirements for parameters, simple simulation models often cannot get correct results, and even the ...; 木犯001号 Power technology

Design of 16-channel data acquisition system based on ADC0809 and 51 single-chip microcomputer: Design a 16-channel data acquisition system (using ADC0890, 8-bit CPU) Requirements: ① The input signal is 0-5V; use the query method to read: get the A/D conversion number; ② Use Protel software to d...; 仁可水北 51mcu

MSP430F449 Experimental Board Schematic Diagram: MSP430F449 Experimental Board Schematic Diagram...; 李岩峰 Microcontroller MCU

Swapped an Embest SoC board: [size=4] [/size] [size=4]I exchanged boards with Zhaoyongke, and now I have Embest's Lark board. The red board looks beautiful! [/size][size=4]At the same time, Zhaoyongke is also a child who loves to...; chenzhufly FPGA/CPLD

Differences between STC89C52 and AT89S52: I just wrote a radio program. It works after burning STC, but it doesn't work properly after burning AT. What's the reason? The following is the program (written in modules) [code]/*******************...; 小杜在此 51mcu

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components