XC6117A217 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > XC6117A217

Preview

XC6117A217: DescriptionCMOS Voltage Detector; File Size519KB，26 Pages; Manufacturer

Download Datasheet View All

XC6117A217 Overview

CMOS Voltage Detector

Preview

Download Datasheet

View All

Preliminary

◆CMOS

Voltage Detector

◆Manual

Reset Input

◆Watchdog

Functions

◆Built-in

Delay Circuit

◆Detect

Voltage Range: 1.6~5.0V, ± 2%

◆Reset

Function is Selectable

DFL

(Low When Detected)

DFH

(High When Detected)

■APPLICATIONS

●Microprocessor

reset circuits

●Memory

battery backup circuits

●System

power-on reset circuits

●Power

failure detection

■GENERAL

DESCRIPTION

■FEATURES

Detect Voltage Range

Hysteresis Range

: 1.6V ~ 5.0V, +2%

(100mV increments)

: V

x 5%, TYP.

(XC6101~XC6107)

x 0.1%, TYP.

(XC6111~XC6117)

: 1.0V ~ 6.0V

The XC6101~XC6107, XC6111~XC6117 series are

groups of high-precision, low current consumption voltage

detectors with manual reset input function and watchdog

functions incorporating CMOS process technology. The

series consist of a reference voltage source, delay circuit,

comparator, and output driver.

With the built-in delay circuit, the XC6101 ~ XC6107,

XC6111 ~ XC6117 series’ ICs do not require any external

components to output signals with release delay time.

Moreover, with the manual reset function, reset can be

asserted at any time. The ICs produce two types of

output; V

DFL

(low when detected) and V

DFH

(high when

detected).

With the XC6101 ~ XC6105, XC6111 ~ XC6115 series’

ICs, the WD pin can be left open if the watchdog function

is not used.

Whenever the watchdog pin is opened, the internal

counter clears before the watchdog timeout occurs.

Since the manual reset pin is internally pulled up to the V

pin voltage level, the ICs can be used with the manual

reset pin left unconnected if the pin is unused.

The detect voltages are internally fixed 1.6V ~ 5.0V in

increments of 100mV, using laser trimming technology.

Six watchdog timeout period settings are available in a

range from 6.25msec to 1.6sec.

Seven release delay time 1 are available in a range from

3.13msec to 1.6sec.

Operating Voltage Range

Detect Voltage Temperature

Characteristics

: +100ppm/

C (TYP.)

Output Configuration

: N-channel open drain,

CMOS

Watchdog Pin

: Watchdog input

If watchdog input maintains

‘H’ or ‘L’ within the watchdog

timeout period, a reset signal

is output to the RESET

output pin

Manual Reset Pin

: When driven ‘H’ to ‘L’ level

signal, the MRB pin voltage

asserts forced reset on the

output pin.

Release Delay Time

: 1.6sec, 400msec, 200msec,

100msec, 50msec, 25msec,

3.13msec (TYP.) can be

selectable.

Watchdog Timeout Period

: 1.6sec, 400msec, 200msec,

100msec, 50msec,

6.25msec (TYP.) can be

selectable.

■TYPICAL

APPLICATION CIRCUIT

■TYPICAL

PERFORMANCE

CHARACTERISTICS

●Supply

Current vs. Input Voltage

XC61X1~XC61X5 (2.7V)

Supply Current:

ISS (µA)

Input Voltage:

VIN (V)

Ta=-40

℃

Ta=25

℃

Ta=85

℃

* Not necessary with CMOS output products.

* ‘x’ represents both ‘0’ and ‘1’. (ex. XC61x1⇒XC6101 and XC6111)

XC6101_07_XC6111_17 ETR0207_009

1/26

Recommended Resources

Do you know about FlexChannel for multi-bus system debugging?

Small two-cell battery booster MAX856 circuit diagram

Leakage protection socket with voice alarm function

Nickel-cadmium battery monitoring circuit

Two-stage inverter circuit with protection diode

2125 and IRF530N: Hello everyone, I made a board, which uses IR2125 for current detection . The schematic diagram of this part is as follows.The D of the power tube is connected to 20V, about 0.6A, the S pin is connect...; xfgood3872 Power technology

Will there be any adverse effects if 0 ohm resistors are used to isolate different grounds?: 1. I DIYed the circuit designed by myself for the quadcopter. The test found that the chip worked normally, the test light could also light up normally, and the mpu6050 could work normally through the...; 赵怡彬 Analog electronics

Can nrf24l01 data be received by a single chip microcomputer? Please provide the code: Does nrf24l01 need two microcontrollers to send and receive? Can I use only one microcontroller? Can you share with me the sending and receiving program of one microcontroller?...; jianhong0425 MCU

Serial port problem: void usrAppInit (void) { #ifdef USER_APPL_INIT USER_APPL_INIT; /* for backwards compatibility */ #endif /* add application specific code here */ int sfd; char accept_buf[1000]; char send[6]={'1','2','...; fossilren Embedded System

Transistor static operating point: Transistor static operating point--------If the static operating point is not set properly, saturation distortion (static operating point is too high) or cutoff distortion (static operating point is t...; QWE4562009 Analog electronics

Freescale embraces Wind River to jointly promote pre-integrated automotive equipment solutions: Wind River Systems and Freescale Semiconductor have announced the availability of a trial version and demonstration kit of their In-Vehicle Device Platform, Wind River's first pre-integrated solution ...; frozenviolet Automotive Electronics

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components