CPB2226000K0SS datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> CPB2226000K0SS

CPB2226000K0SS: DescriptionSpecial Switch; CategoryMechanical and electronic products switch; File Size185KB，4 Pages; ManufacturerAPEM; Environmental Compliance

Download Datasheet Parametric View All

CPB2226000K0SS Overview

Special Switch

CPB2226000K0SS Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	2066945390
Reach Compliance Code	unknown
ECCN code	EAR99
Manufacturer's serial number	CP

Preview

Download Datasheet

View All

CP series

New!

Capacitive switches

Distinctive features and specifications

❑

Activated by the touch of a finger

Even with surgeon gloves

❑

50 million cycles

❑

Auto-calibration function

❑

Bushing diameter 16, 19 or 22 mm

❑

Momentary or latching

ENVIRONMENTAL SPECIFICATIONS

MATERIALS

• Sealing : IP68 and IP69K according to IEC 60529

• Triggered by flowing water

• Impact resistance : IK10

• Operating temperature : -20°C to +65°C

• ESD : complies with EN61000-4-2 (extended) ± 8KV (20 contacts)

and ± 15KV (20 air discharges)

ELECTRICAL AND GENERAL SPECIFICATIONS

• Case : aluminium, anodized

• Multi-wire leads section 0,22 mm

length 300 mm

• Cable, length 300 mm, section

depending on switch model

• Connector : HE14 6V compatible

with AMP/TYCO281839-3

ADJUSTABLE SENSITIVITY

• Max. current/voltage rating : 200mA 24VDC

• Supply voltage : 5 to 24VDC

• Life expectancy : 50 million cycles

• Power consumption non-illuminated : 7mA

• Power consumption illuminated : 25mA

• Operating force : 0N

• LED state for output image option :

1 LED : the LED is ON when the output is closed.

2 LEDs : first colour is ON when the output is open. Second colour is ON

when the output is closed.

• Output type : NPN

Connection to ground by means of the

yellow wire increases sensitivity

(momentary version only).

This switch should not be used

in safety applications.

Wiring diagrams

Non-illuminated

1 LED

Output indicator

2 LEDs

Independent

Output indicator

Independent

Legend

red

Black black

W white

yellow

green

Blue blue

GND

output

sensitivity

-LED 1

-LED2

OFF-ON

Black

Blue G

Black

OFF-MOM

Black

Wire colours may vary.

Always refer to the label

on the switch.

Black

Blue G

Black

Wiring for switch connector

Pin 1 : GND

Pin 2 : output

Pin 3 : +V

Pin 4 : LED 2

Pin 5 : sensitivity

Pin 6 : LED 1

Chamfer

APEM

www.apem.com

B2-125

Recommended Resources

Egg heating control circuit

Simple AC power short circuit protection circuit

Pulse width modulation switching regulated power supply circuit diagram composed of NE555

light dimmer

Photoelectric isolation feedback amplifier TPS5904 application circuit

Threshold NOT gate circuit with front-stage gate resistor

EEWORLD University ---- STM32Cube: Make STM32 development easier: STM32Cube: Make STM32 development easier : https://training.eeworld.com.cn/course/2260STM32Cube: Making STM32 development easier...; chenyy Embedded System

I can't bear it anymore.. Can I use STM32 instead of FX2?: This week I have read a lot of things about FX2 (CY7C68013) and tried to adjust the board I have. The examples I received before were based on the EZUSB kit. They are sometimes good and sometimes bad....; astwyg FPGA/CPLD

Battery Management Tips for Hybrid and Electric Vehicles: For hybrid electric vehicles (HEV) and electric vehicles (EV), the use of lithium-ion batteries provides the best balance between power, energy density, efficiency and environmental impact. However, l...; holy20052005 Power technology

How to install QNX operating system on Beaglebone blak: [i=s]This post was last edited by wsdymg on 2017-11-9 20:17[/i] After two days of hard work, I finally implemented the porting of the QNX operating system on Beaglebone Black. During this period, I re...; wsdymg Embedded System

Renesas R7F0C80212 User Experience (1) - Starting from Scratch: [p=30, 2, left][size=5] It has been almost half a month since I got the board. I have only now completely figured out how to use the board. I have encountered many strange problems in the process of e...; xinmeng_wit Renesas Electronics MCUs

WM5.0 PPC cannot connect directly to SQL Server 2005 on the network. What's going on?: Help is urgent! No RDA seems to be required for sql2005 configuration, now conn.open() connection reports login failure! Tried various connection strings Standard Security: "Data Source=Aron1;Initial ...; yj3333 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components