2.0 GENERAL DESCRIPTION ......................................................................................................................................... 5
6.0 ORDERING INFORMATION ...................................................................................................................................... 8
9.13 Program ................................................................................................................................................................. 18
9.14 Accelerated Program ............................................................................................................................................. 18
10.0 FLASH MEMORY STATUS FLAGS ......................................................................................................................... 22
11.0 Deep Power Down .................................................................................................................................................... 24
12.0 Common Flash Memory Interface............................................................................................................................. 25
13.0 ABSOLUTE MAXIMUM RATINGS ........................................................................................................................... 27
15.0 DC CHARACTERISTICS .......................................................................................................................................... 28
17.0 CAPACITANCE(TA = 25 °C, VCC = 1.8V, f = 1.0MHz)............................................................................................ 29
18.0 AC TEST CONDITION.............................................................................................................................................. 30
19.0 AC CHARACTERISTICS .......................................................................................................................................... 30
20.0 Crossing of First Word Boundary in Burst Read Mode ............................................................................................. 45
-4-
K8S1215E(T/B/Z)C
datasheet
Rev. 1.1
NOR FLASH MEMORY
512M Bit (32M x16) Muxed Burst / Multi Bank SLC NOR Flash Memory
1.0 FEATURES
•
Single Voltage, 1.7V to 1.95V for Read and Write operations
•
Organization
- 33,554,432 x 16 bit (Word Mode Only)
•
Multiplexed Data and Address for reduction of interconnections
I simulated a howland current source. Why does the output produce this kind of self-excited oscillation? If I use other chips, such as AD8056, it will not oscillate....
The screen used is BYD's 3.5-inch TFT screen. The following is the information of the TFT screen driver chip HX8238: HX8238 timing diagram [img] http://lh4.ggpht.com/lijinyan3000/SP_47v0CnNI/AAAAAAAAA...
I wanted to use supercapacitors to compare power consumption in different situations. Since it was for testing, I didn't have too many requirements, so I asked the purchasing department to buy a 5.5V/...
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
There are many types and styles of digital voltmeters in design and development. Traditional digital voltmeters have their own characteristics. They are suitable for manual measurement on site. Tra...[Details]
1 Introduction
CAN (Controller Area Network) bus is a kind of field bus. It is used in many industrial sectors due to its outstanding advantages such as high performance, high reliability, high...[Details]
Single-chip microcomputer is the abbreviation of single-chip microcomputer. It is made by integrating CPU, ROM, RAM, TIMER/COUNTER and input/output interface (I/O) on a large-scale integrated circu...[Details]