REVISION B
DO NOT
SCALE FROM
THIS PRINT
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
"A" REF
(SEE TABLE 2, SHT 6)
"B" REF
(SEE TABLE 2, SHT 6)
C
8.28 .33
C
12.00 .472
P04
P02
"F"
(SEE TABLE 4, SHT 6)
3.195 .126
REF
C
LPHT-XX-XX-X-RTX-XX
POWER POS (TOTAL)
**-02, -04, -06, -08,
**-10, *-12, *-14
SIGNAL POS (TOTAL)
*-12, -16, -20, -24,
-28, -32, *-36, *-40
OPTIONS
-GP: GUIDE POSTS
(LEAVE BLANK FOR NO -GP OPTION)
**-BLANK: NO GP OPTION
*-HS: HOT SWAP
(ONE BANK OF OUTER POWER POS ARE
LONG PINS, POWER PIN ONLY)
(NOT AVAILABLE ON -02 POWER POS)
(LEAVE BLANK FOR NO HOT SWAP)
TAIL
-RT1:RA-TH, 1.58[.062] BOARD
**-RT2: RA-TH, 2.36[.093] BOARD
"D"
PLATING SPECIFICATION
-L: 10 µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
-S: 30 µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
13
LPHT-04-24-X-RTX-GP
24
"C"
(* = NOT TOOLED)
(** = NOT RELEASED)
7.49 .295
REF
C
C
L
4.06 .160 REF
"E"±0.30 C
P03
P01
12
"D"±0.30
"C"
C "G"
(SEE TABLE 4, SHT 6)
LPHT-XX-XX-RA-GP
0.64 .025
REF (TYP)
"D"
02
01
0.45 .018 REF (TYP)
1.27 .050 (TYP)
(TOL NON-ACCUM)
C
"C" REF
(SEE TABLE 2, SHT 6)
3.07 .121
REF
13.93 .548
REF
3.30 .130
REF
16.28 .641
REF
3.07 .121
REF
3.30 .130
REF
'A'
DETAIL 'A'
SCALE 4 : 1
C 2.46 .097
2.50 .098 (TYP) REF
10.00 .394
REF
'B'
FIG 1
3.84 .151
C
DETAIL 'B'
SCALE 4 : 1
3.25 .128
REF
LPHT-04-24-X-RTX-GP SHOWN
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS.
TOLERANCES ARE:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: SIGNAL PIN: 0.5 LBS, POWER PIN: 3.0 LBS.
3. MAXIMUM ALLOWABLE BOW: 0.15[.006] MM/MM AFTER ASSEMBLY.
4. MAXIMUM BURR ON SHEARED TAILS: 0.10[.004].
5. ALL P/N`S REQUIRE PRESSING TO PCB DUE TO ALIGNMENT PEGS,
CONTACT SAMTEC FOR REQUIRED FIXTURES.
6. ASSEMBLIES TO BE PACKAGED IN TRAYS.
DECIMALS
X.X: 0.3 [.01]
2
X.XX: 0.13 [.005]
X.XXX: 0.051 [.0020]
ANGLES
MATERIAL:
INSULATORS: LCP, COLOR: BLACK
SIGNAL TERMINAL: BRASS
POWER TERMINAL: COPPER ALLOY
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
LPHT-RA TERMINAL ASSEMBLY
F:\DWG\MISC\MKTG\LPHT-XX-XX-X-RTX-XX-MKT.SLDDRW
BY:
ROY LUO
LPHT-XX-XX-X-RTX-XX
11/28/2011
SHEET
1
OF
6
REVISION B
LPHT-08-24-X-RTX-GP-HS SHOWN
(DIFFERENT AS SHOWN,OTHERWISE SAME AS FIG 1)
(NOT TOOLED)
FIG 2
C
1.63±0.10 .064±.004
C
L
LPHT-XX-X-RA-GP
T-1M112-XX-X
"E"
"F"
P04
P02
24
13
LPHT-XX-RA
0.25 .010 REF (TYP)
(SEE NOTE 4)
C 1.27 .050 (TYP)
C 2.54 .100
C OF A-PIN
L
"E"
C
"F"
P03
P01
12
02
01
0.75±0.20 .030±.008 (2 PLCS ONLY)
2.25±0.20 .089±.008 (TYP)
C
SECTION "C"-"C"
SCALE 6 : 1
C
0.75±0.20 .030±.008 (TYP)
T-1M110-01-XX-X-ST
DETAIL 'G'
SCALE 4 : 1
C
C
L
1.56±0.05 .062±.002
DETAIL 'H'
SCALE 4 : 1
T-1M110-01-XX-X-ST
'G'
'H'
T-1M110-01-XX-X-HS
T-1M110-02-XX-X-ST
T-1M110-02-XX-X-ST
T-1M110-02-XX-X-HS
SECTION "E"-"E"
SCALE 2 : 1
PROPRIETARY NOTE
SECTION "F"-"F"
SCALE 2 : 1
0.51 .020 REF (TYP)
C 1.23 .048
C
C OF A-PIN
L
2.50 .098
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
SECTION "D"-"D"
SCALE 6 : 1
F:\DWG\MISC\MKTG\LPHT-XX-XX-X-RTX-XX-MKT.SLDDRW
LPHT-RA TERMINAL ASSEMBLY
BY:
ROY LUO
LPHT-XX-XX-X-RTX-XX
11/28/2011
SHEET
2
OF
6
REVISION B
0.86 .034 C
T-1M112-XX-X
T-1M112-XX-X
"H" MIN
LPHT-XX-XX-RA-XX
T-1M112-XX-X
T-1M112-XX-X
T-1M112-XX-X
REMOVE TIE BARS FOR T-1M112-XX-X
IN-PROCESS 1
FILL SIGNAL BOTTOM ROW
0.86 .034
C
IN-PROCESS 2
CUT OFF CARRIER
IN-PROCESS 3
"J" MIN
T-1M112-XX-X
T-1M112-XX-X
T-1M112-XX-X
T-1M112-XX-X
C
L
1.63±0.10 .064±.004
2.54 .100 REF
1.27 .050 REF
C OF A-PIN
L
C
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
CUT OFF CARRIER
IN-PROCESS 6
FORM SIGNAL BOTTOM ROW
IN-PROCESS 4
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
FILL SIGNAL TOP ROW
F:\DWG\MISC\MKTG\LPHT-XX-XX-X-RTX-XX-MKT.SLDDRW
IN-PROCESS 5
LPHT-RA TERMINAL ASSEMBLY
SHEET SCALE: 3:1
BY:
ROY LUO
LPHT-XX-XX-X-RTX-XX
11/28/2011
SHEET
3
OF
6
REVISION B
"J"
C
0.00
+0.15
+.006
0.00
-.000
[
]
T-1M112-XX-X
LPHT-XX-RA
16.27 .641
2.54 .100 REF
1.27 .050 REF
C OF A-PIN
L
"J"
IN-PROCESS 8
FILL LPHT-XX-RA
C
FORM SIGNAL TOP ROW
IN-PROCESS 7
SECTION "J"-"J"
"K"
0.37 .015
C
"E"±0.30
(SEE TABLE 1, SHT 1)
R0.16 .006
15° (TYP)
C
DETAIL 'L'
SCALE 10 : 1
'L'
"K"
1.27 .050 (TYP)
C 2.54 .100
C OF A-PIN
L
SHEAR TAIL & COIN PIN
IN-PROCESS 9
SECTION "K"-"K"
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
LPHT-RA TERMINAL ASSEMBLY
F:\DWG\MISC\MKTG\LPHT-XX-XX-X-RTX-XX-MKT.SLDDRW
BY:
ROY LUO
LPHT-XX-XX-X-RTX-XX
11/28/2011
SHEET
4
OF
6
REVISION B
"M"
LPHT-XX-XX-RA-XX
T-1M110-02-XX-X-XX
T-1M110-02-XX-X-XX
1.23 .048
C
"K"±0.15
90°±1° C
C
C
"D"±0.30
(SEE TABLE 1, SHT 1)
SECTION "M"-"M"
"M"
(FILL POWER BOTTOM ROW)
IN-PROCESS 11
R0.51 .020
"N"
(FORM T-1M110-02-XX-X-XX)
C
1.56±0.05 .062±.002
T-1M110-01-XX-X-XX
IN-PROCESS 10
C
L
T-1M110-01-XX-X-XX
C
"D"±0.30
(SEE TABLE 1, SHT 1)
2.50 .098
90°±1°
C
1.27 .050
C
"L"±0.15
"N"
SECTION "N"-"N"
(FILL POWER TOP ROW)
IN-PROCESS 13
R0.51 .020
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
(FORM T-1M110-01-XX-X-XX)
F:\DWG\MISC\MKTG\LPHT-XX-XX-X-RTX-XX-MKT.SLDDRW
IN-PROCESS 12
DO NOT SCALE DRAWING
SHEET SCALE: 3:1
LPHT-RA TERMINAL ASSEMBLY
LPHT-XX-XX-X-RTX-XX
11/28/2011
SHEET
5
OF
6
BY:
ROY LUO
京公网安备 11010802033920号
EEWORLD
