EEWORLDEEWORLDEEWORLD

Part Number

Search

C1210Y823M9RACTU

Description
multilayer ceramic capacitors mlcc - smd/smt 6.3volts 82000pf 20% x7r
CategoryPassive components   
File Size722KB,18 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Environmental Compliance
Download Datasheet Parametric View All

C1210Y823M9RACTU Overview

multilayer ceramic capacitors mlcc - smd/smt 6.3volts 82000pf 20% x7r

C1210Y823M9RACTU Parametric

Parameter NameAttribute value
ManufactureKeme
Product CategoryMultilayer Ceramic Capacitors MLCC - SMD/SMT
RoHSYes
Capacitance0.082 uF
Voltage Rating6.3 V
Tolerance20 %
Temperature Coefficient / Code+/- 15 %
Case Code - i1210
Case Code - mm3225
ProducOpen Mode/Fail-Safe MLCC
DielectricX7R
Maximum Operating Temperature+ 125 C
Minimum Operating Temperature- 55 C
Package / Case1210 (3225 metric)
PackagingReel
Factory Pack Quantity4000
Termination StyleSMD/SMT
TypeFloating Electrode Design with Flexible Termination System FF-CAP, X7R Dielectric, Commercial
Voltage Rating DC6.3 V
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Floating Electrode Design with Flexible Termination System
(FF-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial & Automotive Grade)
Overview
KEMET’s Floating Electrode with Flexible Termination capacitor
(FF-CAP) combines two existing KEMET technologies–
Floating Electrode and Flexible Termination. The floating
electrode component utilizes a cascading internal electrode
design configured to form multiple capacitors in series within
a single monolithic structure. This unique configuration results
in enhanced voltage and ESD performance over standard
capacitor designs while allowing for a fail-open condition if
mechanically damaged (cracked). The flexible termination
component utilizes a conductive silver epoxy between the base
metal and nickel barrier layers of KEMET’s standard termination
system in order to establish pliability while maintaining terminal
strength, solderability and electrical performance. Both
technologies address the primary failure mode of MLCCs– flex
cracks, which are typically the result of excessive tensile and
shear stresses produced during board flexure and thermal
cycling.
Although neither technology can eliminate the potential for
mechanical damage that may propagate during extreme
environmental and/or handling conditions, the combination of
these two technologies provide the ultimate level of protection
against a low IR or short circuit condition. The FF-CAP
complements KEMET’s Open Mode, Floating Electrode (FE-CAP),
Flexible Termination (FT-CAP) and KEMET Power Solutions (KPS)
product lines by providing an ultimate fail-safe design optimized
for low to mid range capacitance values. These devices exhibit a
predictable change in capacitance with respect to time and voltage
and boast a minimal change in capacitance with reference to
ambient temperature. Capacitance change is limited to ±15% from
-55°C to +125°C.
In addition to Commercial Grade, Automotive Grade devices
are available which meet the demanding Automotive Electronics
Council's AEC–Q200 qualification requirements.
Ordering Information
C
Ceramic
0805
Y
104
Capacitance
Code (pF)
2 Significant
Digits + Number
of Zeros
K
Capacitance
Tolerance
J = ±5%
K = ±10%
M = ±20%
5
Voltage
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
2 = 200 V
A = 250 V
R
Dielectric
R = X7R
A
C
TU
Packaging/Grade
(C-Spec)
2
Blank = Bulk
TU = 7" Reel
Unmarked
TM = 7" Reel Marked
Case Size
Specification/
(L" x W")
Series
0603
0805
1206
1210
1812
Y = Floating
Electrode
with Flexible
Termination
Failure Rate/
Termination Finish
1
Design
A = N/A
C = 100% Matte Sn
L = SnPb (5%
minimum)
Additional termination finish options may be available. Contact KEMET for details.
SnPb termination finish option is not available on automotive grade product.
2
Additional reeling or packaging options may be available. Contact KEMET for details.
1
1,2
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1015_X7R_FF-CAP_SMD • 11/13/2013
1
[I contribute to the Xilinx Resource Center] An example of NTSC signal generation by a foreigner
An example of NTSC signal generation by a foreignerCircuit diagram, instructions, source code, everything...
wanghongyang FPGA/CPLD
Pass the test
[i=s]This post was last edited by paulhyde on 2014-9-15 03:54[/i]Has anyone made the last step of the simple resistance tester? Let's discuss it....
13246806181 Electronics Design Contest
[Collection][E-book] A very touching story (a bit long)
An e-book with a very touching story. . . [:'(] ------ "If I can, I would rather grow old faster, so that I can be with my brother, together."If a girl is willing to exchange her youth for the opportu...
SuperStar515 Embedded System
My understanding of the ProtocolReceivePacket function in the Passthru routine
I spent a lot of time researching the ProtocolReceivePacket function. Some materials mentioned that this function can receive multiple packets, but I think it can only receive complete packets. The re...
kiahe Embedded System
Thermal Micro Printer Reference Design
Thermal Micro Printer Reference Design with Block Diagram...
taburiss001 Microcontroller MCU
Bell Effect
The Bell Effect means that if you think about success, the image of success will form in your heart. The person who proposed it was Bell, an American evangelist and scholar. [b]Typical Case[/b][b]Form...
白丁 Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2054  279  1719  1039  195  42  6  35  21  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号