EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL0BLF-03-2742-D-C

Description
Array/Network Resistor, Bussed, Thin Film, 0.1W, 27400ohm, 0.5% +/-Tol, -25,25ppm/Cel, 5030,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GL0BLF-03-2742-D-C Overview

Array/Network Resistor, Bussed, Thin Film, 0.1W, 27400ohm, 0.5% +/-Tol, -25,25ppm/Cel, 5030,

GUB-GL0BLF-03-2742-D-C Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795494898
package instructionSMT, 5030
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.2
structureMolded
JESD-609 codee3
Network TypeBussed
Number of terminals20
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length12.802 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.1 W
resistance27400 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code5030
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance0.5%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Moderators please advise
Moderator, please advise.I made a board using STM32F101C8and wrote the following program. My purpose is to output high and low level square waves from PORT B.The program was compiled with 0 error and ...
hero362631780 stm32/stm8
The temperature sensor displays the error "The temp is : <7"
Please help me, I am using the ZigBee development board from NetBee. It was tested and was good when I first bought it (resistance value 10K, baud rate 115200, and I also tried 9600). When I was doing...
xiazheng RF/Wirelessly
Share 28335 SCI communication problem summary
1. First, the interrupt setting service program in non-FIFO mode cannot directly enter the sending interrupt; you need to send a byte of data before entering the interrupt; According to the 51 mode, w...
Jacktang Microcontroller MCU
HyperLynx High-Speed Circuit Design and Simulation (VI) Non-ideal Transmission Line Differential Pair Eye Diagram (Impedance Mismatch)
# HyperLynx High-Speed Circuit Design and Simulation (VI) Non-ideal Transmission Line Differential Pair Eye Diagram (Impedance Mismatch) ##1. Construct a non-ideal differential pair circuit diagram###...
bqgup Creative Market
Apply for the moderator of [zigbee tribe], please support me :)
I'm applying to be a moderator :). I have been engaged in Zigbee research for two years. I am familiar with TI's Zigbee solution, have my own small ZIGBEE products, and have experience in several Zigb...
kata RF/Wirelessly
MSP430 series difference
I would like to ask the experts what is the difference between msp430f1xxx and msp430f2xxx series, please recommend a better 430 learning development board...
sodiao Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 867  142  1450  2406  968  18  3  30  49  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号