EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342E12B232BSBS

Description
Fixed Resistor, Thin Film, 0.1W, 232000ohm, 50V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0603, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342E12B232BSBS Overview

Fixed Resistor, Thin Film, 0.1W, 232000ohm, 50V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0603, CHIP

M55342E12B232BSBS Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid262626689
package instructionCHIP
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL8
Other featuresNON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length1.6256 mm
Package formSMT
Package width0.8128 mm
method of packingBulk
Rated power dissipation(P)0.1 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance232000 Ω
Resistor typeFIXED RESISTOR
size code0603
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTIN LEAD OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Research and Design of SDTVHDTV Conversion Based on FPGA
...
至芯科技FPGA大牛 FPGA/CPLD
What does this addition and subtraction circuit do here?
The input waveform in front of C44 is a sine wave of about tens to hundreds of mV. After being amplified by the first op amp, it enters the second op amp U7B, where it is still amplified and then conv...
天天1 Analog electronics
[Project Outsourcing] Make a MOS switch and test it
Make a mos switch and test itProject budget:¥5,000~10,000 Development cycle: 20 days Project Category: Embedded Bidding requirements:Project tag:mosProject Description: It is necessary to design and m...
CSTO项目交易 Power technology
I had nothing to do, so I drew a Crayon Shinchan
The arc is really hard to draw, so it is a little deformed. The water drop is the most perfect one in my opinion....
平行电 PCB Design
How to convert 0~10v voltage input to 10~0v voltage output?
Then use the potentiometer to make the input voltage and output voltage have a linear proportional relationship. Please help me, thank you....
mba03gl Analog electronics
Why is NEXT grayed out when I open the example?
Why when I open the example, which NEXT is grayed out? I opened it before and it was not like this.I found that some of them are grayed out, and some are not....
陈纬 NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 991  1730  1128  1796  1095  20  35  23  37  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号