HIGH PERFORMANCE DP3T-SPDT SWITCHES PLATINUM Series
PAGE
1/12
ISSUE
07-01-2015
SERIES
DP3T/SPDT
PART NUMBER
R595 XXX XXX
DP3T-SPDT Coaxial Switches DC to 6 GHz, DC to 20 GHz, DC to 26.5 GHz, DC to 40 GHz
Radiall’s PLATINUM SERIES switches are optimised to perform at a high level over an extended life span. With outstanding RF
performances, and a guaranteed Insertion Loss repeatability of 0.03 dB over a life span of 10 million switching cycles. PLATINUM
SERIES switches are perfect for automated test and measurement equipment, as well as signal monitoring devices.
PART NUMBER SELECTION
R595_______
RF Connectors :
3 : SMA up to 6 GHz
4 : SMA up to 20 GHz
F : SMA up to 26.5 GHz
8 : SMA 2.9 up to 40 GHz (1)
TYPE :
3 : Latching
4 : Latching + Indicators
5 : Latching + Self Cut-Off
6 : Latching + Self Cut-Off + Indicators
ACTUATOR VOLTAGE :
3 : 24Vdc
7 : 15Vdc
DOCUMENTATION :
- : Certificate Of Conformity
C : Calibration certificate
R : Calibration certificate
+ RF curves
ACTUATOR TERMINAL :
0 :Solder pins
5 : D-Sub connector
OPTIONS :
1 : Without option (Positive common)
2 : Compatible TTL driver (High level)
Switch model :
1 : Non terminated SPDT switch
2 : Terminated SPDT switch
3 : Terminated 4 port bypass switch
4 : Non terminated 5 port DP3T switch
(1)
Connector SMA2.9 is equivalent to “K Connector
®
”, registered trademark of Anritsu
PICTURE
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written agreement
from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
HIGH PERFORMANCE DP3T-SPDT SWITCHES PLATINUM Series
PAGE
2/12
ISSUE
07-01-2015
SERIES
DP3T/SPDT
PART NUMBER
R595 XXX XXX
RF PERFORMANCES
PART NUMBER
Frequency Range
GHz
Impedance
Ohms
Insertion Loss dB
(Maximum)
Isolation dB
(Minimum)
R5953-----
DC to 6
R5954-----
DC to 20
50
0.20 + (0.45 / 26.5) x frequency (GHz)
DC to 6 GHz : 85
6 to 12.4 GHz : 75
12.4 to 20 GHz : 65
DC to 6 GHz : 85
6 to 12.4 GHz : 75
12.4 to 20 GHz : 65
20 to 26.5 GHz : 60
DC to 6 GHz : 1.15
6 to 12.4 GHz : 1.25
12.4 to 20 GHz : 1.30
20 to 26.5 GHz : 1.60
DC to 6 GHz : 85
6 to 12.4 GHz : 75
12.4 to 20 GHz : 65
20 to 26.5 GHz : 60
26.5 to 40 GHz : 55
DC to 6 GHz : 1.15
6 to 12.4 GHz : 1.25
12.4 to 20 GHz : 1.30
18 to 26.5 GHz : 1.60
26.5 to 40 GHz : 1.80
R595F-----
DC to 26.5
R5958-----
DC to 40
85
V.S.W.R.
(Maximum)
Third order Inter Modulation
Repeatability
(up to 10 million cycles
measured at 25°C)
1.15
DC to 6 GHz : 1.15
6 to 12.4 GHz : 1.25
12.4 to 20 GHz : 1.30
-120 dBc typical (2 carriers 20W)
0.03 dB maximum
0.05 dB maximum
TYPICAL RF PERFORMANCES
Insertion Loss and Isolation :
26.5GHz model with SMA connector
40GHz model with SMA2.9 connector
V.S.W.R :
26.5GHz model with SMA connector
40GHz model with SMA2.9 connector
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written agreement
from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
HIGH PERFORMANCE DP3T-SPDT SWITCHES PLATINUM Series
PAGE
3/12
ISSUE
07-01-2015
SERIES
DP3T/SPDT
PART NUMBER
R595 XXX XXX
ADDITIONAL SPECIFICATIONS
Operating mode
Nominal operating voltage (Vdc)
(across operating temperature)
Coil resistance (+/-10%) (Ohms)
Nominal operating current at 23°C (mA)
All models
Average power
Terminated model
High Level
TTL input
Low Level
SPDT
Terminated SPDT, DP3T, Bypass
Latching
24
(20 / 32)
350
175
15
(12 / 20)
120
60
SPDT
68
125
Terminated SPDT, DP3T, Bypass
140
250
RF path
Cold switching : See Power Rating Chart on final page
Hot switching : 1 Watt CW
Internal terminaisons 1 Watt average into 50
External terminations 0.5 Watt average into 50
3 to 7 V
800 µA max at 7 V
0 to 0.8 V
15
10 million cycles
5 million cycles
SMA – SMA 2.9
D-Sub pin female
Solder pins
< 60
< 100
20 µA max at 0.8V
Switching time max (ms)
Life min for
SMA
SMA 2.9
Connectors
Actuator terminal
Weight max (g)
SPDT
Terminated SPDT, DP3T,
Bypass
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
(°C)
Storage temperature range
(°C)
Temperature cycling
(MIL-STD-202 , Method 107D , Cond.A) (°C)
Sine vibration operating
(MIL STD 202 , Method 204D , Cond.D)
Random vibration operating
Shock operating
(MIL STD 202 , Method 213B , Cond.G)
Humidity operating
Humidity storage
(MIL STD 202 , Method 106E , Cond.E)
Altitude operating
Altitude storage
(MIL STD 202 , Method 105C , Cond.B)
-25 to +75
-55 to +85
-55 to +85 (10 cycles)
10-2000 Hz, 20g
16.91g (rms) 50–2000 Hz 3min/axis
50g / 11 ms, sawtooth
15 to 95% relative humidity
65°C, 95% RH, 10 days
15,000 feet (4,600 meters)
50,000 feet (15,240 meters)
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written agreement
from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
HIGH PERFORMANCE DP3T-SPDT SWITCHES PLATINUM Series
PAGE
4/12
ISSUE
07-01-2015
SERIES
DP3T/SPDT
PART NUMBER
R595 XXX XXX
SWITCH MODEL 1 : NON TERMINATED SPDT SWITCH
The non-terminated SPDT switch is a single pole double throw switch. This switch is “break before make”.
RF SCHEMATIC DIAGRAM
Position E1
Position E2
INDICATORS POSITION
State “11”
State “22”
Standard drive option “1” (Positive common):
Connect pin +Vcc to supply
Select desired RF path by applying ground to the
corresponding "Close" pin (Ex: ground pin E1 to switch to
position E1. RF path 1-2 closed and RF path 2-3 open).
To open desired path and close the new RF path, connect
ground to the corresponding “close” pin (Ex: ground pin E2
to open RF path 1-2 and close RF path 2-3)
TTL drive option “2”
Connect pin GND to ground.
Connect pin +Vcc to supply
Select (close) desired RF path by applying TTL "High " to
the corresponding "drive" pin (Ex: apply TTL "High" to pin
E1 to switch to position E1. RF path 1-2 closed and RF
path 2-3 open).
To open desired path and close the new RF path, apply
TTL "High" to the "drive" pin which corresponds to the
desired RF path.
(Ex: apply TTL “High” to pin E2 to open RF path 1-2 and
close RF path 2-3).
D-Sub connector
Solder pins
D-Sub connector
Solder pins
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written agreement
from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
HIGH PERFORMANCE DP3T-SPDT SWITCHES PLATINUM Series
PAGE
5/12
ISSUE
07-01-2015
SERIES
DP3T/SPDT
PART NUMBER
R595 XXX XXX
All dimensions are in inches/millimetres.
With D-Sub connector
With solder pins
Connectors
SMA up to 26.5GHz
SMA 2.9 up to 40GHz
A max (inches / mm)
0.307 / 7.50
0.248 / 6.30
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written agreement
from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
How are short and open defined in RF? Thanks. It seems to be very different from the short and open in low frequency as we understand them. Can an expert explain it in detail?...
1. Does anyone have the source code for the demo? 2. What is the Code Composer Essentials 2.0 that comes with the CD? Is it a compiler software similar to VC? Does it have any advantages? Has anyone d...
Samsung 2440 WinCE CameraTest test program can display images normally on my development board, but the BMP image saved after taking a photo is distorted. I don't know where to start, please give me s...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
Laird Thermal Systems has introduced the HiTemp ET series Peltier cooler modules, which can operate at high temperatures and provide on-site cooling for sensitive electronic devices.
Dig...[Details]
A patent disclosed by Ford proposes replacing traditional segmented side curtain airbags with integrated full-width side curtain airbags that span the side of the vehicle and can be deployed simult...[Details]
The MCX E series is the most reliability- and safety-focused series in NXP's extensive MCX product portfolio.
With the launch of this series, NXP has further enriched its 5V-compatible MCU pr...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
In the period after the switching power supply achieved the "20 kHz" revolution in the 1970s, although improvements and enhancements were made in circuit technology, the development level of the se...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]
The driving mode is not unfamiliar to vehicles. According to the driving mode of the vehicle, there are front-wheel drive, rear-wheel drive and even four-wheel drive. Four-wheel drive is a major se...[Details]
As a pioneer in the new smart home concept, robot vacuums have captured a significant market share. Robot vacuums, also known as automatic sweepers, smart vacuums, or robot vacuums, are smart home ...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
