EEWORLDEEWORLDEEWORLD

Part Number

Search

UTN-62.32KOHMS1%

Description
Fixed Resistor, Wire Wound, 5W, 2320ohm, 504V, 1% +/-Tol, 20ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size261KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

UTN-62.32KOHMS1% Overview

Fixed Resistor, Wire Wound, 5W, 2320ohm, 504V, 1% +/-Tol, 20ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

UTN-62.32KOHMS1% Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7017850577
package instructionAXIAL LEADED, ROHS COMPLIANT
Reach Compliance Codecompliant
Country Of OriginIsrael
ECCN codeEAR99
YTEOL10
Other featuresNON INDUCTIVE
structureTubular
JESD-609 codee3
Lead diameter1 mm
Lead length25.4 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature275 °C
Minimum operating temperature-55 °C
Package diameter7.9 mm
Package length25.4 mm
Package shapeTUBULAR PACKAGE
Package formAxial
Rated power dissipation(P)5 W
Rated temperature25 °C
GuidelineMIL-R-26
resistance2320 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient20 ppm/°C
Terminal surfaceTin (Sn)
Terminal shapeWIRE
Tolerance1%
Operating Voltage504 V
UT Series
FEATURES
Resistances from 0.02 to 320kOhms
Power Rating 0.1 to 13Watts
Resistance Tolerances to ± 0.01%
Low TCR: ± 20ppm/K Standard
MIL-R-26 / MIL-R-39007 Power Ratings
Temperature Range: -55°C to +350°C (V)
Non-Inductive Windings Available
TABLE 1—SPECIFICATIONS
Tolerances
Temperature Coefficient
±0.01% to ±10% ( 1% Standard )
>10W : ±20ppm/K
1W to10W : ±50ppm/K
<1W : Call Factory
-55°C to +275°C : Characteristic U
-55°C to +350°C : Characteristic V
500 VAC : UT-1 / UT-1/2A / UT-1/2 / UT-1A
1000 VAC : All Others
Centerless ground ceramic core
Tinned copper or copperweld leads
High temperature / trivalent / inorganic Silicone coating
All welded terminations
Temperature Range
Dielectric Strength
Constuction
Environmental Performance
(MIL-STD 202)
DR
Characteristic U
±0.2% + 0.05W
±1% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.1% + 0.05W
±0.1% + 0.05W
Characteristic V
±0.2% + 0.05W
±3% + 0.05W
±2% + 0.05W
±2% + 0.05W
±2% + 0.05W
±2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
Dielectric
Load Life
Storage
Moisture Resistance
Thermal Shock
5X Overload ( 5s )
Shock
Vibration
FIGURE 1—DERATING
120
100
Power (%)
80
60
40
20
0
0
25
50
100 150 200 275
Ambient Temperature (°C)
300
350
Char V
Char U
ORDERING INFORMATION
Part Number - Resistance - Tolerance - TCR ( If not standard )
UT-5 25kOhms 0.1%
For Non-Inductive Windings / insert the letter “N” ( i.e. UTN-5 )
Document No.: 64327
Revision: 31-01-2015
For technical questions,
contact
powertron@vpgsensors.com
www.powertron.de
1
Compile and debug ESP32 programs in VSCode
# Compile and debug ESP32 program in VSCode * Take Win10 as an example, Linux is similar. * The debugger takes CMSIS-DAP v2 as an example. If you use the official FTDI or Jlink, the configuration will...
le062 Embedded System
12V lithium battery charging problem
[i=s]This post was last edited by ena on 2016-1-6 15:09[/i] I have a 12V lithium battery in my hand now. When I wanted to charge it, it wouldn't charge. After I cut the seal and touched the circuit bo...
ena Power technology
Crystal Oscillator Circuit
The 3M crystal oscillator circuit can start oscillating, but the output waveform amplitude (about 12V, the power supply is only 9V) is too large, what should I do? (Note: I have adjusted the matching ...
xxhhzz Integrated technical exchanges
Dual power supply automatic switching circuit
Can this circuit realize automatic switching of dual power supplies? It should be switched and then output by a three-terminal regulator, right?...
寒冰翼love Power technology
Sate4412 Development Board Programming Tutorial V1.1.PDF
Compared with "Sate4412 Development Board Burning Tutorial V1.0.PDF", it adds the setting photos of the DIP switch to prevent some netizens from accidentally setting the wrong settings and causing the...
gooogleman Embedded System
Oh, the almighty forum, can anyone tell me how to get power from a telephone line?
Recently I saw a kind of electric lamp that can be directly connected to the telephone line to draw electricity for lighting. Although it is not very bright, it seems to be a good night light.I have n...
小丸子 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2276  1889  1070  2244  2215  46  39  22  45  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号