FMXMB2318GEB-27.000000M-BI datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMB2318GEB-27.000000M-BI

FMXMB2318GEB-27.000000M-BI: DescriptionQuartz Crystal,; CategoryPassive components Crystal/resonator; File Size260KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMB2318GEB-27.000000M-BI Overview

Quartz Crystal,

FMXMB2318GEB-27.000000M-BI Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145048981239
package instruction	HC-49/US, 2 PIN
Reach Compliance Code	compliant
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - 3RD OVERTONE
Drive level	50 µW
frequency stability	0.0015%
frequency tolerance	25 ppm
load capacitance	18 pF
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	27 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
physical size	L11.5XB4.65XH3.2 (mm)/L0.453XB0.183XH0.126 (inch)
Series resistance	120 Ω
surface mount	NO

Preview

Download Datasheet

View All

FMXMB

SERIES

Thru-hole Crystals

Low Profile

Thru-Hole Package

Multiple Package Heights

Low Cost

HC-49/US

SPECIFICATIONS

Issue 6 - 10182012

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

All specifications subject to change without notice.

Specification

3.2 - 90 MHz

See Operation Mode and ESR Table

18 pF Std., 8 - 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-55 to +125°C

See Operation Mode and ESR Table

7 pF max.

50 uW typical, 1 mW max.

±5 ppm per year max.

HC-49/US

OPERATION MODE AND ESR TABLE

Frequency (MHz)

3.200 - 5.999

6.000 - 7.999

8.000 - 9.999

10.00 - 14.99

15.000 - 40.000

27.000 - 70.000

MODE

Fundamental

Overtone

MAX ESR (Ohms)

180

100

120

DIMENSION “H” TABLE

STANDARD MARKING

FMI XX.XXX

XX.XXX FREQUENCY in MHz

Package

Max. Height

0.161” (4.1mm)

0.126” (3.2mm)

0.118” (3.0mm)

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM B1 1 18 H J A - XX.XXXXXXM - CM

Product Family

Crystal

Package

B1,

B2 or B3

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

## - Custom (pF)

Cal.

Tol. @ 25°C

±10 ppm

±15 ppm

±20 ppm

±25 ppm

±30 ppm

±40 ppm

±50 ppm

Custom

*Temp. Tol.

D ±10 ppm

E ±15 ppm

F ±20 ppm

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ± 50 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

BI - Base Insulator

LT - Lead Trimming

LF - Lead Forming

PD - Parameter Data

TD - Temp. Data

CM - Custom Mark

BLANK - None Req’d.

**Check with us for availability.

-55°C TO +125°C Available, Limited Stability Options,

please consult the factory.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

Radio local oscillator circuit

One of the thyristor cut-off delay circuits

Connection between PLC and frequency converter a

Fuse blown sound and light alarm circuit 2

48V/50A rectifier module DC/DC main circuit

Microprocessor power supply circuit diagram using LT1587-3.45

About DMX512 Lighting Protocol: About DMX512 lighting protocol!...; czc568 51mcu

Post an egg: ...; lysk1229 Embedded System

g2553 driver 12864 can not drive: The program is as follows. I connected the cs pin to vcc and used a 12864 with a 5v voltage. I previously suspected that the display was not displayed because the pin was only 3.3v, but then I added a...; 嘎嘎嘎646 Microcontroller MCU

Three ways to write fennel beans: Three ways to write fennel beans, high-side DC current detection switch solution 1, TI's 169 and 5050, cost 10 yuan (excluding power mosfet, the same below) solution 2, use rail-to-rail op to replace ...; PowerAnts Talking

There is a problem with serial port debugging. Experts, please come in and analyze the situation: There is a relatively large program with a display and other functions. Now I need to modify the original serial port program. During the single-step debugging process, once the program reaches the pa...; aahellaa Microcontroller MCU

EVC---About ShellExecuteEx calling executable files: In EVC, call an executable file A with ShellExecuteEx(&A); But if the file A is being executed, how to switch to the executable A without letting it execute again? How to achieve it? Experts, please a...; xheshui Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components