EEWORLDEEWORLDEEWORLD

Part Number

Search

3GPW62G-C-30N-FREQ

Description
LVPECL Output Clock Oscillator, 0.75MHz Min, 200MHz Max, ROHS COMPLIANT, SMD, 6 PIN
CategoryPassive components    oscillator   
File Size100KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GPW62G-C-30N-FREQ Overview

LVPECL Output Clock Oscillator, 0.75MHz Min, 200MHz Max, ROHS COMPLIANT, SMD, 6 PIN

3GPW62G-C-30N-FREQ Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompli
Other featuresTRISTATE; ENABLE/DISABLE FUNCTION; COMPLIMENTARY OUTPUT
Maximum control voltage2 V
Minimum control voltage1.3 V
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate30 ppm
frequency stability100%
Installation featuresSURFACE MOUNT
Maximum operating frequency200 MHz
Minimum operating frequency0.75 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVPECL
Output load50 OHM
physical size11.4mm x 9.6mm x 2.5mm
longest rise time0.7 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
Frequency range 750kHz to 800MHz
LVPECL Output
Supply Voltage 3.3 VDC
Phase jitter 2.35ps typical
Pull range from ±30ppm to ±150ppm
DESCRIPTION
GPW62 VCXOs are packaged in a 6 pad 7mm x 5mm SMD package.
Typical phase jitter for GPW series VCXOs is 2.35ps. Output is
LVPECL. Applications include phase lock loop, SONET/ATM, set-top
boxes, MPEG , audio/video modulation, video game consoles and
HDTV.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
RMS Period Jitter:
Peak to Peak Jitter:
Phase Jitter:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
GPW62 LVPECL VCXO
11.4 x 9.6 x 2.5mm 6 pad SMD VCXO
OUTLINE & DIMENSIONS
Pulling Range:
Control Voltage Range:
Temperature Stability:
Output Load:
Rise/Fall Times:
Duty Cycle:
Start-up Time:
Current Consumption:
Static Discharge Protection:
Storage Temperature:
Ageing:
Enable/Disable:
RoHS Status:
750.0kHz to 800.0MHz
3.3 VDC ±5%
LVPECL
4.3ps typical
27.0ps typical
2.35ps typical
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
Vdd-1.025V minimum
Vdd-0.880V maximum
Vdd-1.810V minimum
Vdd-1.620V maximum
(RL=50 to Vdd-2V)
From ±30ppm to ±150ppm
1.65 ±0.35 Volts
See table
50 into Vdd or Thevenin equiv.
0.5ns typ., 0.7ns max.
20% Vdd to 80% Vdd
50% ±5%
(Measured at Vdd-1.3V)
10ms maximum, 5ms typical
75mA maximum at 212.5MHz
80mA maximum at 622.08MHz
2kV maximum
-55° to +150°C
±2ppm per year maximum
See table
Fully compliant or non-complaint
versions available
FREQUENCY STABILITY
PART NUMBERING
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
Example:
3GPW62G-B-80N-60.000
ENABLE/DISABLE FUNCTION
Tristate Pad
Status
Not connected
Below 0.3Vdd
(Ref. to ground)
Above 0.7Vdd
(Ref. to ground)
Output Status
LVPECL and Complimentary LVPECL enabled
Both outputs are disabled (high impedance)
Both outputs are enabled
Supply Voltage
3 = +3.3V
Series Designator
GPW62
RoHS Status
G = RoHs compliant
Blank = RoHS non-compliant
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk
Automotive Resistive Bridge Pressure Sensor Interface Reference Design
[i=s]This post was last edited by Jacktang on 2019-6-17 12:01[/i]As small as a pen tip!!! TIDA-00793 is an automotive resistive bridge pressure sensor interface reference design. This reference design...
Jacktang Analogue and Mixed Signal
Use of s3c2440 interrupt
I saw an adc driver code that used request_irq(); but there was no statement in the program to turn on the adc interrupt enable bit of the interrupt-related register. I am a novice who switched from M...
sphshine Linux and Android
Display driver problem under WINCE5.0
I'm debugging a TFT screen recently, and the words on the screen are ghosting. I don't know what the problem is? I hope there are experts who can give me some advice....
crazydream Embedded System
【Prizes are being given out】Show your DIY
The heavy social work takes up too much of our time. Outside of the eight-hour workday, do the EEWORLD forum members still cherish our former dreams and hobbies, and have been quietly exploring and st...
eric_wang DIY/Open Source Hardware
80 humorous and philosophical quotes
1. It is better to live beautifully than to be beautiful!    2. When you lose your belt, you will know what dependence is.    3. Cigarettes are disobedient, so we "smoke".    4. If you get angry for o...
wateras1 Talking about work
[Atmel SAM R21 Creative Competition Weekly Plan] + ZLLDEMO + (colorSceneRemote) scene remote control hardware construction
【Atmel SAM R21 Creative Competition Weekly Plan】+ZLLDEMO+(colorSceneRemote)Scene Remote Control Hardware ConstructionBasic Hardware1. SAMR21 XPLAINED pro board2. OLED display hardware occupies IO reso...
蓝雨夜 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2105  754  2548  487  1762  43  16  52  10  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号