EEWORLDEEWORLDEEWORLD

Part Number

Search

T551B706K015AT42527293

Description
Tantalum Capacitor, Tantalum (solid Polymer),
CategoryPassive components    capacitor   
File Size956KB,16 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Download Datasheet Parametric View All

T551B706K015AT42527293 Overview

Tantalum Capacitor, Tantalum (solid Polymer),

T551B706K015AT42527293 Parametric

Parameter NameAttribute value
Objectid7263065254
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL6.9
Other featuresESR IS MEASURED AT 100KHZ, RIPPLE CURRENT IS MEASURED AT 40KHZ, 85CEL
capacitance70 µF
Capacitor typeTANTALUM CAPACITOR
diameter7.09 mm
dielectric materialsTANTALUM (SOLID POLYMER)
ESR140 mΩ
leakage current0.0079 mA
length16.51 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formAxial
method of packingAMMO PACK
polarityPOLARIZED
positive tolerance10%
Rated (DC) voltage (URdc)15 V
ripple current1400 mA
surface mountNO
Delta tangent0.05
Terminal shapeWIRE
Tantalum Polymer Capacitors – Hermetically Sealed
T551 Axial & T556 Surface Mount 125°C
Overview
The T551 axial leaded and T556 surface mount polymer
hermetically sealed (PHS) devices are tantalum capacitors
with a Ta anode and Ta
2
O
5
dielectric. A conductive,
organic polymer replaces the traditionally used MnO
2
or
wet electrolyte as the cathode plate of the capacitor. The
result is very low ESR and improved capacitance retention
at high frequency and low temperature. The PHS device
also exhibits a benign failure mode, which eliminates the
case breach that can occur in wet tantalum capacitors.
Additionally, the part may be operated at voltages up to
80% of rated voltage, with equivalent or better reliability
than traditional MnO
2
or wet tantalum capacitors operated
at 50% of rated voltage.
PHS capacitors molded also offer higher ripple current
handling capability and a lower ESR range than wet
tantalums. With reduced ESR and enhanced capacitance
retention at higher frequencies and low temperatures, these
parts provide the highest total capacitance and the most
economical solution for high power applications, all within an
approximately 25% lighter package than the equivalent wet
tantalum capacitor.
Benefits
• Includes F-Tech anode, which eliminates hidden defects in
the dielectric
• 100% simulated breakdown screening
• Maximum operating temperature of +125°C
• Polymer cathode technology
• ≤ 0.0075 CV (µA) at rated voltage after 5 minutes
• Extremely low ESR
• High frequency and low temperature capacitance retention
• 100% constant voltage conditioning (240 hours)
• 100% surge current tested
• Volumetrically efficient
• Use at up to 80% of rated voltage
• Non-ignition failure mode
• Approximately 25% lighter than equivalent wet tantalum
• T551 case dimensions equivalent to
MIL-PRF-39006/22/25/30/31
• T556 surface mount design (see dimensions diagram)
One world. One KEMET
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
T2072_T551 • 3/31/2020
1
Realization of Low Frequency Signal Generator Using Single Chip Microcomputer
The design task requirements of the signal generator are: 1) Frequency range: 100Hz~1MHz; 2) Can generate triangle wave, square wave and sine wave; 3) Stable output voltage, Vopp=6V; Performance part:...
bds489550896 Embedded System
Call for action: DIY Internet radio using LM3S8962
This is Moen's suggestion: LM3S8962 has 256KB FLASH, 64KB SRAM, CAN, 10/100 ETH, 10bit ADC, PWM. The price of a single chip seems a bit high, but compared with similar products such as: STM32 series M...
soso Microcontroller MCU
Contiki(2) How to start and purpose
Obviously, now that I have decided not to worry about this or that, and I have discovered that Contiki contains much more than I imagined. So an idea has become stronger and stronger in my heart: Forg...
辛昕 RF/Wirelessly
Can 0 ohm resistors be connected in series on several SPI lines?
I use SPI between my STM32 and CPLD, and each SPI port line is connected in series with a 0 ohm resistor. Now SPI communication is not working. Is it because of the series resistor?...
kelywu stm32/stm8
CC2541 Bluetooth pcb antenna gain calculation
RT, I'm a newbie, can anyone give me some guidance?...
顺手牵→猪 PCB Design
LED flasher operating at low voltage
The low voltage microprocessor supervisory circuit can form a low voltage, low power LED flasher, and can adjust the lighting time and flashing rate. The μP supervisory circuit (IC1) is powered by two...
lorant Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2205  2576  1098  103  1022  45  52  23  3  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号