ZWS100AF24/J datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> ZWS100AF24/J

ZWS100AF24/J: Descriptionswitching power supplies 103w 24v 4.3A; CategoryPower/power management; File Size535KB，2 Pages; ManufacturerTDK Corporation; Websitehttp://www.tdk.com; Environmental Compliance

Download Datasheet Parametric View All

ZWS100AF24/J Overview

switching power supplies 103w 24v 4.3A

ZWS100AF24/J Parametric

Parameter Name	Attribute value
Manufacture	TDK-Lambd
Product Category	Switching Power Supplies
RoHS	Yes
Produc	Switching Supplies
Open Frame/Enclosed	Open Frame
Output Power Rating	103 W
Input Voltage	85 VAC to 265 VAC
Number of Outputs	1 Outpu
Output Voltage-Channel 1	24 V
Output Current-Channel 1	4.3 A
Commercial/Medical	Commercial
Length	3.7 i
Width	5 i
Heigh	1.4 i
Approvals	UL60950-1, EN60950-1
Dimensions	3.7 in L x 5 in W

Preview

Download Datasheet

View All

ZWS-AF Series

50W to 150W Single Output Low Cost, Worldwide Use

Features

Universal Input (85 - 265VAC)

Power factor Corrected

Input transient protected

2 year warranty

High quality design

Peak Power capability

Key Market Segments & Applications

Speciﬁcations

Model

AC Input Voltage range

DC Input Voltage range

Input Current (Typ) (1)

Inrush Current

Power Factor (1)

Maximum Ripple and Noise

Temperature Coefﬁcient

Overcurrent Protection (4)

Hold Up Time (Typ) (1)

Leakage Current

Remote On / Off

Operating Temperature

Storage Temperature

Humidity (non condensing)

Withstand Voltage

Isolation Resistance

Vibration (non operating)

Shock

Safety Agency Approvals

Conducted & Radiated EMI

Immunity

Weight (Typ)

Size (W x H x D)

Warranty

VAC

VDC

yrs

ZWS75AF

ZWS100AF

ZWS150AF

85-265VAC (47-63Hz)

120-370VDC

0.8/0.4

1.2/0.6

1.4/0.7

2.0/1.0

14/28 25°C Ambient, Cold Start

Meets EN61000-3-2 (0.99/0.95)

3.3 & 5V: 120mV; 12 to 24V: 150mV; 36 & 48V: 200mV

<0.02%/°C

>105% of Peak Current Capability

20ms

0.5mA max 0.1mA (Typ) at 100VAC 0.16mA (Typ) at 230VAC

See installation manual (Not available with /A cover option)

Convection cooling - See table on page 2

0.7m/s air -10°C to +70°C, derate linearly to 70% load from 60°C to 70°C (2)

-30° to +85°C

Operating: 30 - 90% RH, storage 10-95% RH

I/P~Grnd 2kVAC (20mA), I/P~O/P 3kVAC (20mA), O/P~Grnd 500VAC (100mA) for 1 min.

>100M at 25C & 70%RH, Output to Ground 500VDC

10 - 55Hz (1 minute sweep), 19.6m/s

constant X, Y, Z 1 hour

< 196.1 m/s

UL60950-1, CSA60950-1, EN60950-1, EN50178, CE Mark

designed to meet EN55011, EN55022-B, FCC Class B, VCCI-B

designed to meet EN61000-4-2,-3,-4,-5,-6,-8,-11

210

290

380

500

55 x 26 x 195

55 x 32 x 222

62 x 35 x 222

75 x 40 x 222

Two Years

ZWS50AF

Notes:

(1) 100/200VAC

(2) ZWS150AF -10 to 60°C, derate linearly to 70% load from 50°C to 60°C

(3) The peak current draw must not exceed a 10 second duration with a duty cycle of 35%

(4) Constant current limit with automatic recovery. Do not operate in a over-load or shorted output condition for more than 30 seconds.

(5) An overvoltage condition on the output will shut down the power supply. The power supply must be re-set by cycling the AC input.

For New Designs, See ZWSBAF Series

1-800-526-2324 • www.us.tdk-lambda.com/lp/

Disclaimer: us.tdk-lambda.com/lp/legal.htm

Recommended Resources

Positive peak detector circuit diagram A

Automatic flush control circuit

Gel battery charger

Contactor interlocking forward and reverse control circuit diagram

Popular satellite TV receiver

Three-phase motor two-speed 2Y/Y connection speed regulating circuit

Can the IO port of MSP430 directly drive the servo?: The servos are MG995 and SG90. Yesterday, I used 3.3V power supply directly, and the MSP430 IO port directly output 20MS cycle PWM to drive the servos. There was no problem except a little shaking. Bu...; 蛊惑小夜 Microcontroller MCU

msp430 application uart driver installation failed, please help: My W732 flagship, it says the driver has been found, but when I try to install it, an error occurs. The method in the previous help post is not useful. Someone said it was a USB cable problem, but it ...; 井头咖 Microcontroller MCU

How can Freescale's MC13224 chip obtain the RSSI value?: I have a Freescale MC13224 development board and a ZigBee positioning project. I know that the distance from the target to the communication node can be obtained through RSSI, but I don't know how to ...; pkltk NXP MCU

Sine wave medium frequency inverter using IGBT: Abstract: This paper introduces the medium frequency inverter power supply using IGBT as power device, and analyzes the working principle of the circuit in detail.Keywords: insulated gate bipolar tran...; zbz0529 Power technology

I'm a newbie, I have a question!!!: When I use mulitism simulation, the voltage of capacitor C1 does not change. Why is this? ! ! !...; yk4711178 Analog electronics

There is a problem: I currently have a project where I am doing system hardware design, that is, the design of a single-board hardware system. I have no idea about system hardware before this and I would like to ask an e...; stevenkean Test/Measurement

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components