The DS1099 is a low-cost, low-power, low-frequency
silicon oscillator that generates two square-wave out-
puts with frequencies between 0.25Hz and 1.048MHz.
Individual output enables allow both outputs to be
enabled/disabled independently. Both outputs are
capable of sinking 16mA, allowing them to directly
interface to light-emitting diodes (LEDs) as well as other
external circuitry. The DS1099 operates over a wide
supply voltage, making it suitable for both 3V and 5V
systems. The device is shipped from the factory custom
programmed and calibrated, ready to be inserted into
the end application.
Contact the factory for custom frequencies or require-
ments.
Features
●
Low-Cost, Low-Frequency EconOscillator™ with
Dual Outputs
●
Factory Programmed
●
Output Frequencies Independently Programmable
from 0.25Hz to 1.048MHz
●
2.7V to 5.5V Single-Supply Operation
●
No External Timing Components Required
●
Independent Output Enables
●
CMOS/TTL-Compatible Outputs
●
Oscillator Outputs Capable of Sinking 16mA to
Directly Drive LEDs
●
Relieves Microprocessor of Periodic Interrupt
●
Low-Power Consumption
●
Operating Temperature Range: -40°C to +125°C
●
±100ppm/°C Temp Drift (max)
Applications
●
●
●
●
●
Flashing LED Status Indicators
Consumer Appliances
Servers
Printers
Switch-Mode Power Supplies
Ordering Information
PART
DS1099U-
a
O
a
1
TEMP RANGE
-40°C to +125°C
PIN-PACKAGE
8 µSOP
*Where
α
0 and
α
1 specify the factory-programmed divider
settings for OUT0 and OUT1, respectively.
Ordering information is continued on the last page.
EconOscillator is a trademark of Maxim Integrated Products, Inc.
Typical Operating Circuit
V
CC
V
CC
Pin Configuration
TOP VIEW
V
CC
OE0
OE1
N.C.
N.C.
DS1099
GND
OUT1
OUT0
OUT1
OUT0
V
CC
1
2
3
8
N.C.
N.C.
OE1
OEO
DS1099
7
6
5
GND 4
OE1 CAN INSTEAD
BE TIED TO V
CC
IF OUT1 IS NOT USED.
OUTPUTS CAPABLE OF
SINKING 16mA
µSOP
19-7629; Rev 2; 5/15
DS1099
Low-Frequency Dual EconOscillator
Absolute Maximum Ratings
Voltage Range on V
CC
Relative to Ground .........-0.5V to +6.0V
Voltage Range on
OE0
and
OE1
Relative to Ground .................................. -0.5V to (V
CC
+ 0.5V),
not to exceed 6.0V
Operating Temperature Range ......................... -40°C to +125°C
Storage Temperature Range ............................ -55°C to +125°C
Soldering Temperature ......................................See IPC/JEDEC
J-STD-020A Specification
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Recommended DC Operating Conditions
(T
A
= -40°C to +125°C)
Supply Voltage
Input Logic 1 (OE0,
OE1)
Input Logic 0 (OE0,
OE1)
PARAMETER
SYMBOL
V
CC
V
IH
V
IL
(Note 1)
CONDITIONS
MIN
2.7
0.7 x
V
CC
-0.3
TYP
MAX
5.5
V
CC
+
0.3
+0.3 x
V
CC
UNITS
V
V
V
DC Electrical Characteristics
PARAMETER
Standby Supply Current
Active Supply Current (Note 2)
High-Level Output Voltage
(OUT0, OUT1)
Low-Level Output Voltage
(OUT0, OUT1)
High-Level Input Current
(OE0,
OE1)
Low-Level Input Current
(OE0,
OE1)
(V
CC
= +2.7V to +5.5V, T
A
= -40°C to +125°C, unless otherwise noted.)
SYMBOL
I
STBY
I
CC
CONDITIONS
OE0
=
OE1
= V
CC
CL = 15pF per output,
OE0
=
OE1
= GND,
V
CC
= 3.3V
V
OH
V
OL
I
IH
I
IL
I
OH
= -1mA, V
CC
= MIN
I
OL
= 16mA (-40°C to +85°C)
I
OL
= 12mA (-40°C to +125°C)
V
IH
= V
CC
V
IL
= 0.0V
-1.0
1.048MHz (both)
4kHz (both)
1Hz (both)
2.4
0.4
+1.0
MIN
TYP
145
323
146
145
V
V
µA
µA
µA
MAX
275
UNITS
µA
www.maximintegrated.com
Maxim Integrated
│
2
DS1099
Low-Frequency Dual EconOscillator
AC Electrical Characteristics
(V
CC
= +2.7V to +5.5V, T
A
= -40°C to +125°C, unless otherwise noted.)
PARAMETER
Master Oscillator Frequency
Nominal Output Frequency
Output Frequency Tolerance
Voltage Frequency Variation
(Note 3)
Temperature Frequency Variation
Output Duty Cycle
Power-Up Time
Output Rise/Fall Time
SYMBOL
f
MOSC
f
OUT0
,
f
OUT1
∆f
OUT
∆f
OUT
∆f
OUT
t
PU
T
A
= +25°C, V
CC
= 4.1V
T
A
= +25°C
2.7V to 5.5V, T
A
= +25°C
(Notes 3, 4)
(Note 5)
C
L
= 15pF (both)
0.25
-1.0
3300
-2.0
-100
45
+2.5
+100
55
10
20
CONDITIONS
MIN
TYP
1.048
1,048,000
+1.0
MAX
UNITS
MHz
Hz
%
ppm/V
%
ppm/°C
%
ms
ns
t
R
, t
F
Note 1:
All voltages referenced to ground.
Note 2:
Active supply current combines the standby current with the output current. The output current is defined by
I = (C
LOAD
+ 12pF ) x V
CC
x f
OUT
for each output when enabled.
Note 3:
This is the change observed in output frequency due to changes in temperature or voltage.
Note 4:
This parameter is guaranteed by design.
Note 5:
This indicates the time between power-up and the outputs becoming active.
Typical Operating Characteristics
(V
CC
= +5.0V, T
A
= +25°C, unless otherwise noted.)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
C
L
= 15pF, T
A
= +25°C
DS1099 toc01
DS1099 toc02
600
SUPPLY CURRENT (µA)
500
400
300
200
100
0
500
400
300
200
100
SUPPLY CURRENT (mA)
SUPPLY CURRENT (µA)
OUT0 = OUT1 = 1MHz
600
OUT0 = OUT1 = 1MHz
1.0
0.8
0.6
0.4
0.2
0
V
CC
= 2.7V
V
CC
= 4.0V
V
CC
= 5.5V
OUT0 =1MHz,
OUT1 = 0.25Hz
OUT0 = OUT1 = 0.25Hz
2.7
3.4
4.1
4.8
5.5
OUT0 =1MHz,
OUT1 = 0.25Hz
OUT0 = OUT1 = 0.25Hz
-40
-15
10
35
60
85
0
0
10
20
C
L
(pF)
30
40
50
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
www.maximintegrated.com
Maxim Integrated
│
3
DS1099 toc03
700
700
SUPPLY CURRENT vs. TEMPERATURE
V
CC
= 5.5V, C
L
= 15pF
1.2
SUPPLY CURRENT vs. OUTPUT LOAD
(BOTH OUTPUTS LOADED EQUALLY), T
A
= +25°C
DS1099
Low-Frequency Dual EconOscillator
Typical Operating Characteristics (continued)
(V
CC
= +5.0V, T
A
= +25°C, unless otherwise noted.)
DS1099 toc04
DS1099 toc05
170
SUPPLY CURRENT (µA)
160
150
140
130
120
110
100
2.7
T
A
= +25°C
T
A
= -40°C
DUTY CYCLE (% CHANGE)
51.0
FREQUENCY (% CHANGE)
0.5
50.0
T
A
= +25°C
49.0
T
A
= +85°C
0
-0.5
3.4
4.1
4.8
5.5
48.0
2.7
3.4
4.1
4.8
5.5
-1.0
2.7
3.4
4.1
4.8
5.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
DS1099 toc07
DS1099 toc08
FREQUENCY (% CHANGE)
0.5
VOLTAGE (V)
0.4
0.3
0.2
0.1
0
V
CC
= 2.7V, T
A
= +25°C
2.7
2.6
VOH (V)
2.5
2.4
2.3
2.2
V
CC
= 2.7V, T
A
= +25°C
0
-0.5
OUT0
OUT1
OUT0
OUT1
-1.0
-40
-15
10
35
60
85
0
5
10
I
OL
(mA)
15
20
-5
-4
-3
-2
-1
0
TEMPERATURE (
°
C)
I
OH
(mA)
Pin Description
PIN
1
2
3
4
5
6
7, 8
NAME
OUT1
OUT0
GND
OE0
OE1
N.C.
V
CC
FUNCTION
Oscillator Outputs. Each output is forced high when the corresponding
OE
is high.
Positive Supply Terminal
Ground
Output Enable for OUT0 and OUT1, respectively. When low, the outputs are enabled. When high, the
corresponding output is disabled (forced high).
No Connection
www.maximintegrated.com
Maxim Integrated
│
4
DS1099 toc09
1.0
FREQUENCY CHANGE vs. TEMPERATURE
f
OUT
= 1MHz, V
CC
= 4.0V, C
L
= 15pF
0.5
OUTPUT VOLTAGE LOW vs. OUTPUT CURRENT
OUTPUT VOLTAGE HIGH vs. OUTPUT CURRENT
2.8
DS1099 toc06
180
SUPPLY CURRENT vs. VOLTAGE
OEO = OE1 = V
CC
52.0
DUTY CYCLE vs. SUPPLY VOLTAGE
OUT0 = OUT1 = 1MHz, C
L
= 15pF
1.0
FREQUENCY CHANGE vs. SUPPLY VOLTAGE
f
OUT
= 1MHz, T
A
= +25
°
C, C
L
= 15pF
DS1099
Low-Frequency Dual EconOscillator
Functional Diagram
V
CC
V
CC
GND
MASTER
OSCILLATOR
1.048MHz
f
MOSC
DIVIDER 0
DIVIDE BY 2
X
(X = X
0
= 0...22)
DS1099
FACTORY-
PROGRAMMED
EEPROM
OUTPUT
DRIVER
f
OUT0
OUT0
DIVIDER 1
DIVIDE BY 2
X
(X = X
1
= 0...22)
OUTPUT f
OUT1
DRIVER
OUT1
OE0
OE1
Detailed Description
The DS1099 consists of a fixed-frequency 1.048MHz
master oscillator followed by two independent facto-
ry-programmable dividers. The two divider outputs
are connected to pins OUT0 and OUT1, which are
Table 1. Divider Settings and Output
Frequencies
DIVIDER SETTING
X
0
OR X
1
0
1
2
3
4
5
—
19
20
21
22
DIVISOR
1
2
4
8
16
32
—
524,288
1,048,576
2,097,152
4,194,304
f
OUT0
OR f
OUT1
1.048MHz
0.524MHz
0.262MHz
0.131MHz
65.50kHz
32.75kHz
—
2Hz
1Hz
0.5Hz
0.25Hz
independently enabled/disabled using the output-enable
pins,
OE0
and
OE1,
respectively. When the output-en-
able pins are active (low), the corresponding outputs are
enabled. If either output-enable pin is tied to its inactive
state (high), then the corresponding output is disabled
and forced high immediately. The output- enable pins only
disable the corresponding output driver(s) and do not shut
down the master oscillator or the dividers.
Since the master oscillator frequency, f
MOSC
, is fixed, the
frequency of OUT0 and OUT1 is determined by DIVIDER
0 and DIVIDER 1, respectively. And since each output
has its own divider, f
OUT0
and f
OUT1
can be programmed
independent of each other.
The frequency of the outputs are calculated as follows:
f
OUT0
= f
MOSC
/2X0 = 1.048MHz/2
X
0
f
OUT1
= f
MOSC
/2X1 = 1.048MHz/2
X
1
where X
0
is the DIVIDER 0 setting and X
1
is the DIVIDER
1 setting. Valid values for X
0
and X
1
are integers 0 to 22
(dec).
Table 1 shows output frequencies and divider values for
I want to make a function that automatically pops up the soft keyboard when the search dialog box pops up. I want to use SipEnumIM to get the input method information, then use the obtained CLSID valu...
A GoKit3
I know how to develop a smart pet house
but
How to transform it into an air quality detector?
Actually, it’s very simple
Just buy one on the almighty Taobao
MQ135 air quality detection sensor...
Why is it that the data of my interrupt-mode TWI bus dual-machine communication (two MEGA48 chips) is correct when simulated under proteus, but the received data is incorrect when downloaded to the mi...
The program needs to initialize the sine table and look it up to find the angle. It stops here and reports an error. The error is Can't read from data memory 0x3FA000, check memory config [-2185]...
Due to various needs, sometimes you may need to do square root on a microcontroller. Here is a method I found on the Internet and would like to share with you.1. Principle : pow(X,Y) represents X rais...
[align=left][font=Helvetica]Embedded systems licensing is the combination of hardware and software into a single product, transforming traditional hardware vendors into innovative software vendors. Th...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Every time I go home and walk up the stairs, I am always scared. The corridor lights are often broken, and no one changes the bulbs, or they are not smart enough and need to be operated manually. E...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
The capacity of a battery depends on the amount of charge and discharge, in addition to some factors of the battery itself. Obviously, if the charge and discharge of the battery can be recorded all...[Details]
As a new type of centralized and decentralized elevator control system, serial communication has been widely used in China. Compared with the previous centralized and unified control system, each s...[Details]
As countries around the world are leaning towards the new energy battery industry, lithium-ion power batteries, as the ideal energy source for the development of the 21st century, are attracting mo...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
