EEWORLDEEWORLDEEWORLD

Part Number

Search

7246R10KT2L.25LT

Description
Potentiometer, Wire Wound, 2W, 10000ohm, 5% +/-Tol,
CategoryPassive components    The resistor   
File Size149KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

7246R10KT2L.25LT Overview

Potentiometer, Wire Wound, 2W, 10000ohm, 5% +/-Tol,

7246R10KT2L.25LT Parametric

Parameter NameAttribute value
Objectid1193429589
Reach Compliance Codecompliant
ECCN codeEAR99
Lead length4.8 mm
Manufacturer's serial number7246
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
Package diameter22.2 mm
Package length37.3 mm
Package formPanel Mount
Rated power dissipation(P)2 W
resistance10000 Ω
Resistor typePOTENTIOMETER
rotation angle3600 deg
series7246
technologyWIRE WOUND
Tolerance5%
September DIY - 6LoWPAN Sniffer
[font=微软雅黑][size=3]I DIYed a 6LoWPAN Sniffer for 780 band when I was free. The chip is stm32+212b. The hardware structure is relatively simple, and the principle is also quite simple. I didn't intend ...
lyzhangxiang RF/Wirelessly
[NXP Rapid IoT Review] Rapid IoT Studio Simple Programming Step 3 Bluetooth Connection Control Test
[NXP Rapid IoT Review] Rapid IoT Studio Simple Programming Step 3 Bluetooth Connection Control Test 1. Open IDE. 2. Add Bluetooth connection control and three page controls. 3. Connect the Bluetooth c...
damiaa RF/Wirelessly
【GD32L233C-START Review】New Construction
[i=s]This post was last edited by paty on 2022-4-14 17:23[/i]1. Create a new project folder " GD32L233_Project ", the folder name can be arbitrary. 2. Create new folders named " Fwlib ", " Project ", ...
paty GD32 MCU
【AT-START-F403A Review】II. Exploration of Simulated Virtual Serial Port
In the last review, I installed a virtual serial port. Of course, it was installed automatically, not by my own will. At that time, I had a question mark in my mind, I thought, ATLINK can actually cre...
ddllxxrr Domestic Chip Exchange
I want to make a control board with DSP28335. Can anyone give me some advice?
I am a beginner in DSP and don't know anything. I want to make a control board using 28335 to control two motors. The drivers of the motors are already available, so I just need to use CAN to send ins...
flyfish1986 Microcontroller MCU
Ask: About cross-compiling Perl
I now want to use perl5.10.0 on a mipsel board. I read the Cross-compilation section in the INSTALL document in its source code (you can also see http://search.cpan.org/~rgarcia/perl/INSTALL#Cross-com...
losty Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2892  2600  2237  1461  2403  59  53  46  30  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号