DIP1987SD031603GF datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1987SD031603GF

DIP1987SD031603GF: DescriptionArray/Network Resistor, Bussed, 0.1W, 160000ohm, 100V, 2% +/-Tol, -25,25ppm/Cel, 7025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

DIP1987SD031603GF Overview

Array/Network Resistor, Bussed, 0.1W, 160000ohm, 100V, 2% +/-Tol, -25,25ppm/Cel, 7025,

DIP1987SD031603GF Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	791661388
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	5.18
structure	Welded
JESD-609 code	e0
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Bussed
Number of terminals	14
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	17.78 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.1 W
resistance	160000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	7025
Temperature Coefficient	25 ppm/°C
Terminal surface	Tin/Lead (Sn60Pb40)
Tolerance	2%
Operating Voltage	100 V

DIP1987SD031603GF Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Current cutoff feedback circuit part 4b

Torque motor single-phase speed regulation circuit 2

Triangular wave and square wave generator circuit diagram installed with NE555

±15V bipolar parallel regulated power supply circuit

Operational transconductance amplifier circuit

Bidirectional thyristor energy consumption braking circuit

What happens if the nstatus pin is always low after the FPGA is powered on?: I just made an EP4SGX230 board, with jtag and as interfaces, but I can't download programs. I measured the nstatus pin (external 10k pull-up to 3.0V) and found that after power-on, the pin is always a...; sharbioue FPGA/CPLD

How many IO are needed to display an 8-segment digital tube? Can one do it?: RT. Can one do it? For example: PA = 0xc0; display 1 0xC0. What is the hardware circuit to display it on the digital tube? My email address is: [email=start133401@hotmail.com]start133401@hotmail.com[/...; start13 MCU

6.6kW Totem Pole PFC Reference Design with 98.6% Efficiency for HEV/EV On-Board Chargers: [align=center][/align] [align=left]In order to help electric vehicles charge quickly, TI provides a 6.6kW totem pole PFC reference design with an efficiency of 98.6% and suitable for HEV/EV on-board c...; alan000345 TI Technology Forum

How to add uart2 under 2440+ce5.0: As the title says, the original bsp package only uses uart1. I added the relevant content of uart2 in platform.reg, and the application can access it, but the uart2 communication is abnormal, and afte...; SiangLiu Embedded System

What occasions are i2c's write, writeto, and write_mem respectively suitable for?: [i=s] This post was last edited by 9zhmke on 2018-2-22 00:52 [/i] I am confused. I wrote a small program to use an infrared positioning sensor. I need to pass a string of initialization information fi...; 9zhmke MicroPython Open Source section

Confused about PIC16F877A sleep current?: MCU is PIC 16F877A, power supply : input DC9V, then output 5V after LM1117-5.0 voltage regulation to power MCU. When testing sleep current, connect the ammeter in series between LM1117 and MCU. There ...; eeleader Microchip MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components