DIP1998021403DG datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1998021403DG

DIP1998021403DG: DescriptionArray/Network Resistor, Bussed, 0.1W, 140000ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 8025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

DIP1998021403DG Overview

Array/Network Resistor, Bussed, 0.1W, 140000ohm, 100V, 0.5% +/-Tol, -50,50ppm/Cel, 8025,

DIP1998021403DG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	791783301
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	6.9
structure	Welded
JESD-609 code	e4
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Bussed
Number of terminals	16
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	20.32 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.1 W
resistance	140000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	8025
Temperature Coefficient	50 ppm/°C
Terminal surface	Gold (Au)
Tolerance	0.5%
Operating Voltage	100 V

DIP1998021403DG Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

38 LED energy-saving lamp circuit

Intelligent control module and computer interface

OPA404 type operational amplifier circuit

RF signal automatic cycle monitoring controller

pocket wireless microphone

Digital Counting Demonstration Circuit

Design and test of switching power supply stability!: [size=3][b]Introduction[/b][/size] [size=3]It is well known that any closed-loop system with a gain of unity gain l and an internal phase shift of 360° with frequency will have the possibility of inst...; 木犯001号 Power technology

Is the AV signal analog or digital?: [size=4]Hello everyone, is the AV signal an analog signal or a digital signal? [/size]...; rabbit-cricket Analog electronics

Transistor Circuit Design (Volumes 1 and 2): This book is one of the "Practical Electronic Circuit Design Series" and is divided into two volumes.The main contents of the first volume include the working principle of transistors, the performance...; arui1999 Download Centre

Jlink V7 burned out, can it be repaired?: My board was hit by AC power, and the Jlink and the computer motherboard were destroyed. When I plugged in the Jlink, the computer prompted that the USB device could not be recognized. I measured the ...; banana MCU

TimerB has two interrupt vectors. How can we set it to enter the second interrupt vector of TimerB?: [i=s]This post was last edited by helloxieyu on 2015-4-10 10:01[/i] int main( void ) { WDTCTL = WDTPW +WDTHOLD; BCSCTL1 = CALBC1_1MHZ; DCOCTL = CALDCO_1MHZ; P1REN|=BIT1; P1DIR|=BIT1; //Interrupt setti...; helloxieyu Microcontroller MCU

About SAM R21 Development Board: What does it mean when the status light on this development board keeps flashing after the USB is plugged in?...; brucelijihui Microchip MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components