EEWORLDEEWORLDEEWORLD

Part Number

Search

GUS-QSCBLF-001582-FF

Description
Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 15800ohm, 100V, 1% +/-Tol, -250,250ppm/Cel, 3415,
CategoryPassive components    The resistor   
File Size365KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUS-QSCBLF-001582-FF Overview

Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 15800ohm, 100V, 1% +/-Tol, -250,250ppm/Cel, 3415,

GUS-QSCBLF-001582-FF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid900456531
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.7
structureMiniature
JESD-609 codee3
Network TypeBussed
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height1.626 mm
Package length8.661 mm
Package formSMT
Package width3.912 mm
method of packingTR
Rated power dissipation(P)0.05 W
resistance15800 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesQSOP
size code3415
technologyTANTALUM NITRIDE/NICKEL CHROME
Temperature Coefficient250 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance1%
Operating Voltage100 V
Surface Mount QSOP
Resistor Networks
QSOP Series
Reliable, no internal cavity
High resistor density - .025" lead spacing
Standard JEDEC 16, 20, and 24 pin packages
Ultra-stable TaNSil
®
resistors on silicon substrate
RoHS compliant and Sn/Pb terminations available
IRC’s TaNSil
®
QSOP resistor networks are the perfect solution for high volume applications that demand a
small wiring board footprint. The 0.025" lead spacing provides higher lead density, increased component
count, lower resistor cost, and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking, low cost
and miniature package. Excellent performance in harsh, humid environments is a trademark of IRC’s
self-passivating TaNSil
®
resistor film.
The QSOP series is ideally suited for the latest surface mount assembly techniques and each lead can be
100% visually inspected. The compliant gull wing leads relieve thermal expansion and contraction stresses
created by soldering and temperature excursions.
For applications requiring high performance resistor networks in a low cost, surface mount package, specify
IRC QSOP resistor networks.
Electrical Data
Resistance Range
Absolute Tolerance
Ratio Tolerance to R1
Absolute TCR
Tracking TCR
Element Power Rating @ 70°C
Isolated Schematic
Bussed Schematic
Package Power Rating @ 70°C
Rated Operating Voltage
______
(not to exceed
P x R)
Operating Temperature
Noise
100mW
50mW
16-Pin
20-Pin
24-Pin
750mW
1.0W
1.0W
10 to 250KΩ
To ±0.1%
To ±0.05%
To ±25ppm/°C
To ±5ppm/°C
Environmental Data
Test Per
MIL-PRF-83401
Typical
Delta R
Max Delta
R
Thermal Shock
±0.02%
±0.1%
Power Conditioning
±0.03%
±0.1%
High Temperature Exposure
±0.03%
±0.05%
Short-time Overload
±0.02%
±0.05%
100 Volts
-55°C to
+125°C
<-30dB
Low Temperature Storage
±0.03%
±0.05%
Life
±0.05%
±2.0%
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
QSOP Series Issue January 2009 Sheet 1 of 4
Energy Design
Are there any people from companies that develop wind energy here?...
unsettled Embedded System
2011-06-16 Hangzhou Pinjia and NXP held a technical seminar on ARM Cortex-M microcontroller
On the afternoon of June 16 , Pinjia Electronics and NXP will hold an ARM Cortex-M microcontroller technical seminar in Hangzhou , and we invite engineers to participate !Registration method: 1. Onlin...
wenshan NXP MCU
LDO Basics: Noise - Part 1
By Aaron Paxton, Texas Instruments In an LDO Basics blog post, I discussed using a low dropout regulator (LDO) to filter the ripple voltage caused by a switch-mode power supply. However, this is not t...
alan000345 TI Technology Forum
A power supply with "FAN": compare how cool your power supply is
[align=left][font=微软雅黑][size=4]People think that the fashion world has style, but I think the electronics world has more style: a world created by losers that is becoming more and more stylish. [/size...
EEWORLD社区 Power technology
Errors caused by placing CLK on a normal pin
CLK-IN放在一个普通脚上,出现错误A clock IOB / clock component pair have been found that are not placed at an optimal clock IOB /下面是代码:module clk_test(clk_in,h_in,v_in,clk_out,h_out);input clk_in;input h_in;input v...
eeleader-mcu FPGA/CPLD
6410 runs at 667 frequency!
How can I make S3C6410 run at 667 frequency under wince6? How to configure it? What should I modify in "S3C6410_SEC_V1\OAL\INC\soc_cfg.h"? When I adjust it to 666, it can't be compiled directly, and a...
yy0216 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1604  712  2743  1155  1275  33  15  56  24  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号