Y145330R0000Q9L datasheet, PDF

Datasheet> All Categories > Passive components> Y145330R0000Q9L

Y145330R0000Q9L: Descriptionres 30 ohm .3W .02% radial; CategoryPassive components; File Size2MB，8 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y145330R0000Q9L Overview

res 30 ohm .3W .02% radial

Y145330R0000Q9L Parametric

Parameter Name	Attribute value
Datasheets
Z Series (Z-Foil)
Standard Package	1,000
Category	Resistors
Family	Through Hole Resistors
Packaging	Bulk
Resistance (Ohms)	30
Tolerance	±0.02%
Power (Watts)	0.3W
Compositi	Metal Foil
Features	Moisture Resistant, Non-Inductive
Temperature Coefficie	±0.2ppm/°C
Package / Case	Radial
Supplier Device Package	-
Size / Dimensi	0.300" L x 0.105" W (7.62mm x 2.67mm)
Heigh	0.336" (8.53mm)
Number of Terminations	2

Preview

Download Datasheet

View All

Z Series (Z-Foil)

Vishay Foil Resistors

Ultra High Precision Z-Foil Though-Hole Resistor

with TCR of ± 0.05 ppm/°C, Tolerance of ± 0.005 % (50 ppm),

Load Life Stability of ± 0.005 %

FEATURES



Temperature coefficient of resistance (TCR):

- ± 0.05 ppm/°C nominal (0 °C to + 60 °C)

- ± 0.2 ppm/°C nominal (- 55 °C to + 125 °C,

+ 25 °C ref.) (see table 1)



Rated power: to 1 W at + 125 °C (see table 2)



Resistance tolerance: to ± 0.005 % (50 ppm)



Load life stability: ± 0.005 % at 70 °C, 2000 h or ±0.015%

at 70°C,10000 h (see table 4)



Resistance range: 5

to

600 k



Vishay Foil Resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)



Total accumulated change in resistance over life (EOL)

or Total Error Budget < 0.1 % (or better with PMO)**



Electrostatic discharge up to 25 000 V



Non-inductive, non-capacitive design



Rise time: 1 ns effectively no ringing



Current noise:

≤

0.010 µV

RMS

/V of applied voltage (< - 40

dB)



Thermal EMF: 0.05 µV/°C typical



Voltage coefficient: < 0.1 ppm/V



Low inductance: < 0.08 µH typical



Thermal stabilization time < 1 s (to reach within 10 ppm of

steady state value)



Pattern design minimizing hot spots



Terminal finish: lead (Pb)-free or tin/lead alloy



Matched sets are available per request



(TCR tracking: to 0.5 ppm/°C)



Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com

INTRODUCTION

The Bulk Metal

Foil resistor is based on a special

thermo-metalic stress concept wherein a proprietary bulk

metal cold rolled foil is cemented to a ceramic substrate. It is

then photoetched into a resistive pattern. Then it is laser

adjusted to any desired value and tolerance. Because the

metals used are not drawn, wound or mistreated in any way

during manufacturing process, the Bulk Metal Foil resistor

maintains all its design, physical and electrical

characteristics while winding of wire or sputtering does not.

Z foil resistors achieve maximum stability and near-zero

TCR. These performance characteristics are built-in for

every unit, and do not rely on screening or other artificial

means for uniform performance.

The stability of a resistor depends primarily on its history of

exposures to temperature. Stability is affected by:

1. Reversible changes in the ambient temperature and heat

from adjacent components (defined by the Temperature

Coefficient of Resistance, or TCR)

2. Short-term steady-state self-heating (defined by Power

TCR or PCR)

3. Irreversible destabilizing shock of suddenly-applied

power

4. Long-term exposure to applied power (load-life stability)

5. Repetitive stresses from being switched on and off

In very high-precision resistors, these effects must be taken

into account to achieve high stability with changes in load

(Joule Effect) and ambient temperature.

Vishay Foil Resistors’ new Z-Foil technology provides an

order of magnitude reduction in the Bulk Metal Foil

element’s sensitivity to temperature changes - both external

and internal. This technology provides TCR of

± 0.05 ppm/°C nominal (instrument range: 0 °C to +60 °C),

± 0.2 ppm/°C nominal (military range: - 55 °C to + 125 °C,

+ 25 °C ref), and a PCR of 5 ppm at rated power.

In order to take full advantage of this TCR improvement, it is

necessary to take into account the differences in the

resistor’s response to each of the above-mentioned effects.

The Z series has been developed to successfully deal with

these factors.

TABLE 1 - NOMINAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

VALUE

100



to 600 K



to < 100



to < 80



to < 50



to < 25



to < 10



STANDARD

TOLERANCE

± 0.005 %

± 0.01 %

± 0.02 %

± 0.05 %

NOMINAL TCR AND

MAX. SPREAD

(ppm/°C)

± 0.2 ± 0.6

± 0.2 ± 0.8

± 0.2 ± 1.0

± 0.2 ± 1.3

± 0.2 ± 1.6

± 0.2 ± 2.3

* Pb containing terminations are not RoHS compliant, exemptions may apply

** See PMO page 5

Document Number: 63187

Revision: 22-Oct-13

For any questions, contact:

foil@vishaypg.com

www.vishayfoilresistors.com

Recommended Resources

Permanent magnet servo motor field oriented control

Inverting AC amplifier circuit composed of LM324

9V nickel-cadmium battery charging circuit diagram

Current regulator circuit with current limit

Alarm circuit diagram

Pyroelectric detection and radio transmission circuit

Why is the AD of my STM8S 0X25~0X30 at 0V?: Why is the AD of my STM8S 0X25~0X30 at 0V? Is the data larger when the voltage is increased? Please give me some advice. Configuration: void ADC_config(void) { GPIO_Init_TypeDef GPIO_InitStructure; AD...; gezich210 stm32/stm8

Transfer: Double Ninth Festival Miyun Tour: In the golden autumn, the weather is clear and refreshing. I always have the urge to "go into the mountains". The impulse is worse than action. Last weekend, I went to Miyun for the last time in 2010 ...; 川波木四 Energy Infrastructure?

How to write data to the ICM7212AM LED driver chip?: Hello friends: P0.0-P0.3 of the microcontroller is connected to B0, B1, B2, B3 of icm7212Am; P0.4, p0.5 are connected to DA1, DA2, P2.0 is connected to CS1 (low level is valid), WR is connected to CS2...; magic_jw Embedded System

Hello everyone! Please help!: OMAPL138 DSP, if you run a bare metal program without a DDR chip, can you download it from NandFlash to the DSP chip? Is this solution feasible?...; folung DSP and ARM Processors

This week's highlights: [b][url=http://www.deyisupport.com/blog/b/thinkinnovative/archive/2016/12/07/52606.aspx]You can rely on a battery drive to keep your device running[/url][/b][font=微软雅黑][size=3] [/size][/font][font=微软雅...; 橙色凯 TI Technology Forum

Issues with switching from Quartus to ModelSim: [size=5][b]Discussion based on the course Altera FPGA Design Skills Improvement Training [url=https://training.eeworld.com.cn/course/575]https://training.eeworld.com.cn/course/575[/url][/b][/size] Wha...; e与或非 FPGA/CPLD

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components