280Z332K104B11 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> 280Z332K104B11

280Z332K104B11: DescriptionPotentiometer, Carbon Composition, 0.125W, 100000ohm, 500V, 20% +/-Tol, 7871; CategoryPassive components The resistor; File Size1MB，4 Pages; ManufacturerCTS; Environmental Compliance

Download Datasheet Parametric View All

280Z332K104B11 Overview

Potentiometer, Carbon Composition, 0.125W, 100000ohm, 500V, 20% +/-Tol, 7871

280Z332K104B11 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1205445892
package instruction	PCB Mount, 7871
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Rotary
Manufacturer's serial number	280(ZV)ZVDT
Package length	19.7 mm
Package form	PCB Mount
Package width	18 mm
Rated power dissipation(P)	0.125 W
resistance	100000 Ω
Resistor type	POTENTIOMETER
rotation angle	300 deg
series	280(ZV)ZVDT
size code	7871
technology	CARBON COMPOSITION
Tolerance	20%
Operating Voltage	500 V

Preview

Download Datasheet

View All

Series 280

Commercial

Miniature

16mm Diameter

Composition

Variable Resistors

• Miniature 16mm style

• Bushing mounted with PC terminals and

shaft parallel or perpendicular to PC board

• Single or multiple section units

• Compatible with CTS 288 series rotary

encoders

Available with:

• Molded or metal shafts

• Push Pull Switch

• Electrical taps

• Center detent

Electrical and Mechanical Specifications

Resistance Range

500 ohms through 5 megohms (linear taper).

Resistance Tolerance

Standard: ±20%

Special tolerances available

Power Rating, Watts

watt per section through 10K ohms

watt per section above 10K ohms

Full rating @ 55°C derated to no load at 85°C

for linear tapers (derating required on

multiple section controls).

Voltage Rating

Bushings to Terminals:

High pot test, one minute — 750 VAC

Operating maximum

— 500 VDC

Across End Terminals:

350 VDC, load not to exceed power rating.

Insulation Resistance

100 megohms minimum dry

Angle of Rotation

Total Rotation:

Without switch — 300° ± 5°

Effective Rotation:

Without switch — 300° (approximate)

Rotation Torque

0.5-4 inch-ounces (36-288 gcm)

Switch Rating

Push pull type: 50mA, 20VDC

Technical Data Sheet 1448C

Technical Data Sheet 1280A

CTS CORPORATION /

MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS

Recommended Resources

Op Amp Linear Sawtooth Generator

Photoelectric control switch circuit

Practical circuit 01 using STK3048 and STK6153

Motor phase failure control and protection circuit

Measurement circuit of inductive displacement sensor

Stable brightness dimming desk lamp circuit

Can Mitsubishi PLC data movement mov instruction mov k150z0 d135 and MOV H0C8E D8120 be like this?: [table=98%,rgb(239, 245, 249)] [tr][td] Can Mitsubishi PLC data movement mov instruction mov k150z0 d135 and MOV H0C8E D8120 be like this? [/td][/tr] [/table]...; boming Industrial Control Electronics

How to open office documents using the command line?: Like vim evince gedit command...; wushaojay Linux and Android

The enet_uip routine of LM3S9B96 cannot be debugged: After configuring the IP and MAC, I directly run the routine program. The LCD screen does not display the IP at all. After adding breakpoints, I found that the debugging did not execute the breakpoint...; 喜鹊王子 Microcontroller MCU

Please answer the reference voltage problem of msp430F4152AD: I'm practicing using msp430F4152 recently, and I have a question: what will happen if different values are used for the AD reference voltage? What is the effect of choosing a higher reference voltage ...; fish001 Microcontroller MCU

KernelIoControl finds the device number problem: Problem of KernelIoControl finding device number if(!KernelIoControl(IOCTL_HAL_REQUEST_SYSINTR,&g_Irq,sizeof(UINT32),&g_SysIntr,sizeof(UINT32),NULL)) { RETAILMSG(1,TEXT("ERROR:Failed to request sysint...; xinbao77 Embedded System

What is the art of plugging vias on PCB boards?: Via hole is also called conduction hole. In order to meet customer requirements, the circuit board conduction hole must be plugged. After a lot of practice, the traditional aluminum sheet plugging pro...; ohahaha PCB Design

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components