Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
Applications
Automotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPGAs
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & Aerospace
Description
CTS Model SA254 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
SA254
Frequency Code
[MHz]
XXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
A
Packaging
R
Code
Frequency
Product Frequency Code
1
Code
1
X
2
3
5
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
±50ppm
Code
I
G
H
N
P
M
Stability
±15ppm
±20ppm
±30ppm
Code
5
6
7
Temp. Range
2
-40°C to +85°C
-40°C to +105°C
3
4
-40°C to +125°C
-40°C to +150°C
5
5
-55°C to +105°C
-55°C to +125°C
5
Packing
Code
3k pcs./reel
R
Code
F
Mode
Fundamental
Code
X
2
3
Stability
±50ppm
±100ppm
±150ppm
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
Series
B
S
Notes:
1]
2]
3]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
Available with all stability codes.
Available with stability codes 3, 5, 6 and 7.
Available with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
Hello everyone! I have a question. The program I wrote runs normally after being burned into FLASH, but after burning LB for encryption, the program does not run normally. I don't know why. Has anyone...
Scan orderFilling order:When the command is 0xa0, from left to rightWhen the command is 0xa1, from right to leftPage scan command:When the command is 0xc0, from bottom to topWhen the command is 0xc8, ...
[color=#4b082][backcolor=rgb(255,250,205)][font=Helvetica, Arial, sans-serif][size=6]「ADI Analog University」Basic Principles of Clock and Timing[/size][/font][/backcolor][/color] [size=5][color=rgb(0,...
How to implement functions like malloc function on ARM processor? The malloc function in the standard library does not need to allocate storage space in advance. I have tested that whether a code has ...
Wang Xiaochuan, the "Wudaokou Goalkeeper", is going through a level that he has never gone through before. For example, Sogou's (NYSE: SOGO) financial report, artificial intelligence, and the futur...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
1. Purpose In actual product release, if the program stored in the MCU Flash is not protected, some illegal companies may read the program in the Flash through an emulator (J-Link, ST-Link, e...[Details]
I have read the source code of mbed these days, and the interface encapsulation for upper-level application calls is quite good. The code quality is relatively high, the comments are also very detai...[Details]
The trade war between China and the United States has become the focus. The United States has begun to play the ban card against Chinese technology companies. The ZTE incident shows that if the ban...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
On April 18-19, 2018, at the "Second Distributed Photovoltaic Carnival" held in Hangzhou, Jinko Power and China New Energy Assets Investment, Financing and Trading Platform (hereinafter referred to as...[Details]
Nowadays, everyone is saying that "technology is people-oriented". The essence of the development of technology is to serve the improvement of the quality of life of human beings. Automated driving...[Details]
STM32 uses FSMC to read and write CPLD programs. CPLD is hung on the address line and data line of STM32. CPLD is regarded as an off-chip RAM for reading and writing. On the board I made, CPLD is hun...[Details]
Recently, Zhejiang Lipu Crushing Equipment Co., Ltd. invested 50 million yuan to build a new "annual production of 1,200 high-efficiency and energy-saving ultra-fine pulverizer construction project...[Details]
Recently, Jiangsu GoodWe Power Technology Co., Ltd. ("GoodWe") unveiled two products of the SDT family, the 17kW smart photovoltaic inverter GW17KN-DT and the 20kW smart photovoltaic inverter GW20KN-D...[Details]
According to the description provided in the official manual of ST, it is not difficult to see that the ADC analog watchdog is actually that the user can set an upper and lower limit of the AD value...[Details]
Today’s medical devices are filled with increasingly complex electronic devices that monitor, display, assist and warn patients. The latest generation of medical device electronic devices are smaller...[Details]
An easy programming question for microcontrollers! Urgent, write a 3-byte binary subtraction subroutine. When using the main program to call multiple groups of data for debugging, two situations need...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
