The IS25LQ025/512/010/020/040B (256K/512K/1M/2M/4M-bit) Serial Flash memory offers a storage solution with
flexibility and performance in a simplified pin count package. ISSI’s “Industry Standard Serial Interface” is for systems
that have limited space, pins, and power. The IS25LQ025/512/010/020/040B is accessed through a 4-wire SPI
Interface consisting of a Serial Data Input (Sl), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#)
pins, which also serve as multi-function I/O pins in Dual and Quad modes (see pin descriptions). The IS25xQ series
of Flash is ideal for code shadowing to RAM, execute in place (XIP) operations, and storing non-volatile data.
The memory array is organized into programmable pages of 256-bytes each. The IS25LQ025/512/010/020/040B
supports page program mode where 1 to 256 bytes of data can be programmed into the memory with one command.
Pages can be erased in groups of 4K-byte sectors, 32K-byte blocks, 64K-byte blocks, and/or the entire chip. The
uniform sectors and blocks allow greater flexibility for a variety of applications requiring solid data retention.
The device supports the standard Serial Peripheral Interface (SPI), Dual/Quad output (SPI), and Dual/Quad I/O (SPI).
Clock frequencies of up to 104MHz for all read modes allow for equivalent clock rates of up to 416MHz (104MHz x 4)
allowing up to 52MBytes/S of throughput. These transfer rates can outperform 16-bit Parallel Flash memories
allowing for efficient memory access for a XIP (execute in place) operation. The IS25LQ025/512/010/020/040B is
manufactured using industry leading non-volatile memory technology and offered in industry standard lead-free
packages. See Ordering Information for the density and package combinations available.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. 0A
10/31/2014
2
PRELIMINARY INFORMATION
IS25LQ025/512/010/020/040B
TABLE OF CONTENTS
FEATURES .......................................................................................................................................................... 2
GENERAL DESCRIPTION .................................................................................................................................. 2
[i=s]This post was last edited by a985872z on 2016-2-3 14:49[/i] Hello everyone, I would like to ask about the connection method of the crystal head: 1. The network cable in my house is: one end is in...
Dear electronics industry experts, I would like to ask you a question and hope to get your answer. In the next 10 years, will the development space of hardware or software be bigger? Now I personally ...
After-class Exercise 22: UCOS Simple Semaphore1. Semaphore (from Mr. Ren Zhe's book)
Semaphores are a type of event. The original purpose of using semaphores is to set a flag for shared resources, whi...
The power supply is burning itself while providing energy to the load. When designing a power supply, people will carefully analyze the load requirements, but they tend to ignore the heat consumption ...
The project I am involved in needs to implement a function to wirelessly control the on and off of LED lights at short distances. The specific requirements are as follows: In a room, there are many bo...
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
1 Introduction
Washing machines are an indispensable household appliance in the home, and they are developing very fast. Fully automatic washing machines are favored by everyone because of their con...[Details]
LonWorks fieldbus technology is widely used, for example, in intelligent buildings, industrial control, environmental protection, etc. Echelon's LonWorks system has been used in the products of tho...[Details]
1. Introduction
With the rapid development of computer technology, communication technology, and integrated circuit technology, the large-scale application of field control instruments and equ...[Details]