EEWORLDEEWORLDEEWORLD

Part Number

Search

76PI2150GY00H

Description
CAPACITOR, METALLIZED FILM
CategoryPassive components    capacitor   
File Size1MB,31 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Environmental Compliance  
Download Datasheet Parametric View All

76PI2150GY00H Overview

CAPACITOR, METALLIZED FILM

76PI2150GY00H Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1324579034
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL7.1
Other featuresESR IS MEASURED AT 100KHZ, RIPPLE CURRENT IS MEASURED AT 100KHZ AND 85CEL
capacitance0.015 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYPROPYLENE
ESR42 mΩ
high11 mm
length18 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance2.5%
Number of terminals2
Maximum operating temperature110 °C
Minimum operating temperature-55 °C
Package formRadial
method of packingTR, 14 INCH
positive tolerance2.5%
Rated (AC) voltage (URac)400 V
Rated (DC) voltage (URdc)630 V
GuidelineAEC-Q200
ripple current2800 mA
surface mountNO
Temperature Coefficient-200+/-100ppm/Cel ppm/°C
Terminal pitch15 mm
Terminal shapeWIRE
width5 mm
Polypropylene Pulse/High Frequency Capacitors
R76, Double Metallized Polypropylene Film,
Radial, DC and Pulse Applications (Automotive Grade)
Overview
The R76 series is constructed of polypropylene film and
double metallized polyester film as electrodes with radial
leads of tinned wire. The radial leads are electrically
welded to the metal layer on the ends of the capacitor
winding. The capacitor is encapsulated in a self-
extinguishing solvent resistant plastic case with
thermosetting resin material meeting UL 94 V–0
requirements. Two different winding constructions are
used depending on voltage parameters. Please see the
Performance Characteristics for more information.
Automotive grade devices (up to lead spacing 22.5 mm)
meet the demanding Automotive Electronics Council's
AEC–Q200 qualification requirements.
Applications
Typical applications include resonant circuit, high frequency
high current, snubber and silicon-controlled rectifier (SCR
and IGBT) and SiC (e.g. MOSFET) commutation circuits as
well as applications with high voltage and high current.
Not suitable for across-the-line application
(see Suppressor Capacitors).
Benefits
• Voltage range: 250 – 2,000 VDC
• Capacitance range: 100 pF – 12 µF
• Lead Spacing: 7.5 mm – 37.5 mm
• Capacitance tolerance: ±2.5%, ±5%, ±10%
• Climatic category: 55/110/56 IEC 60068–1
• Operating temperature range of −55°C to +110°C
• RoHS compliance and lead-free terminations
• Tape & Reel packaging in accordance with IEC 60286–2
• Self-healing
• Automotive (AEC–Q200) grades available up to lead
spacing 22.5 mm
Part Number System
R76
Series
Double
Metallized
Polypropylene
I
Rated Voltage
(VDC)
I = 250
M = 400
P = 630
Q = 1,000
T = 1,600
U = 2,000
D
Lead Spacing
(mm)
D = 7.5
F = 10
I = 15
N = 22.5
R = 27.5
W = 37.5
1680
Capacitance
Code (pF)
The last three
digits represent
significant figures.
The first digit
specifies the total
number of zeros to
be added.
SE
Packaging
See Ordering
Options Table
00
10
20
30
40
30
Internal Use
50
60
70
80
L0
K
Capacitance
Tolerance
H = ±2.5% (*)
J = ±5%
K = ±10%
(*) = for C ≥ 1,000 pF
Built Into Tomorrow
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3034_R76 • 1/13/2022
1
GD32E231 DIY Part 4: Software Architecture
[i=s]This post was last edited by Li Baiyi on 2019-5-18 20:38[/i]Software architecture: [font=宋体][size=4]1. Firmware library file: [/size][/font][font=宋体][size=4]GD32E23x_Firmware_Library[/size][/font...
李百仪 GD32 MCU
Design ideas of lightning arrester for monitoring system
I. Overview: --- A monitoring system (hereinafter referred to as monitoring system) is an auxiliary equipment for technical prevention and scientific management. At the beginning of its introduction, ...
aq2 Industrial Control Electronics
DDS signal source based on single chip microcomputer and FPGA
[i=s] This post was last edited by paulhyde on 2014-9-15 03:10 [/i] DDS signal source based on microcontroller and FPGA...
pspcxl Electronics Design Contest
Show the WEBENCH design process + FPGA power supply design process
[i=s] This post was last edited by gaon on 2014-7-23 16:34 [/i] Use the FPGA Power Design Tool to record, select the FPGA Power Design Tool tab, the following interface appears, click the PROCESSER bu...
gaon Analogue and Mixed Signal
What is SiC (Silicon Carbide)? The difference between SiC-MOS and Si-MOS
[i=s]This post was last edited by qwqwqw2088 on 2020-3-29 11:22[/i]Silicon carbide (SiC) is a relatively new semiconductor material. To begin with, let's take a look at its physical properties and cha...
qwqwqw2088 Analogue and Mixed Signal
【ESP32 Learning】Usage of ADC
In ESP32, two 12-bit successive approximation digital-to-analog converters are built in, managed by five dedicated converter controllers, which can measure analog signals from 18 pins. The ADC can als...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1517  661  2549  2286  1305  31  14  52  47  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号