EEWORLDEEWORLDEEWORLD

Part Number

Search

LSZ7J1A7A

Description
Basic/quick action/limit switch lmt-SW/SP replacemnt plug-in assy
CategoryTopical application    Mechanical and electrical/engineering/automation   
File Size429KB,4 Pages
ManufacturerHoneywell
Websitehttp://www.ssec.honeywell.com/
Download Datasheet Parametric View All

LSZ7J1A7A Overview

Basic/quick action/limit switch lmt-SW/SP replacemnt plug-in assy

LSZ7J1A7A Parametric

Parameter NameAttribute value
MakerHoneywell
RoHSno
ActuatorRotary, T
Termination typeScrew
Installation Instructions for the
HDLS Series Switches
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency
stop devices or in any other application where failure
of the product could result in personal injury.
Failure to comply with these instructions could
result in death or serious injury.
MOUNTING
All Heavy Duty Limit Switches (HDLS) have exactly the
same mounting dimensions. Mount by either of two
methods: (a) use two #10 screws from the front, or (b)
use two #10-32 UNF screws from the back. HDLS offers
the advantage of front mount construction. The
electrician will find a complete switch, with no parts
missing and ample wiring space.
With plug-in construction, wiring and conduit connection
is made to the base receptacle. This feature also
reduces downtime, since plug-in unit can be removed
without disconnecting wiring or conduit.
To mount either switch, merely tighten mounting screws,
tighten plug-in unit or cover screws, and make sure
conduit section is sealed. Use of sealant (teflon tape,
pipe dope, etc.) is recommended to seal conduit
connection.
Because of moisture condensation problems, it is not
good practice to mount the switch upside down or at the
low point of conduit runs.
Sealing
Enclosure Type
ISSUE 2
PK 81116
IP67/68
1, 3, 3R, 4, 4X, 6, 6P, 12, 13
Rated Operational Voltages (Ue) and Currents (Ie)
Ue
Ie
120 Vac
6A
600 Vac
1.2 A
125 Vdc
0.22 A
250 Vdc
0.11 A
WIRING
Use size #12AWG or smaller solid or
stranded wire to connect to the
pressure type connector terminals.
Spades may be up to .312" wide,
rings up to .312" dia. With spade or
ring type connections, preinsulated
connectors or heat-shrinkable tubing
should be used to provide insulation
between terminals. Circuit diagram is
shown on the nameplate.
It will be easier to wire the double-
pole units by connecting lead wires to
the terminals nearest the conduit opening first. A
grounding screw is located in the housing near the
conduit opening.
Switch units with an indicator light in the cover are
furnished with the lead wires from the light connected to
the normally-open male terminals (#3 and #4) unless
otherwise specified on the order. Wires can be
unsoldered and reconnected to the normally-closed male
terminals or they can be ordered connected to the
normally-closed terminals by using a modification code
(refer to Catalog 40). Always connect these wires to the
same set of terminals used for the load. Across the
normally open male terminals (#3 and #4) the light will
be On (Fig. 1). Across the normally closed terminals (#1
and #2) the light will be Off.
Single-Pole – Plug-in Type
Double-Pole – Non
Plug-in Type
Sensing and Control
Welcome to the world of consumer electronics
[i=s] This post was last edited by jameswangsynnex on 2015-3-3 20:00 [/i] I hope that through our joint efforts, the consumer electronics section will become more and more popular! [Y] I would like to...
lorant Mobile and portable
LKT4101 8-bit dual protocol anti-copy board encryption chip encryption ic
The LKT4101 anti-copy board dedicated coprocessor chip adopts a dedicated smart card chip platform, with a built-in embedded system independently developed by Linkcore Security, a new generation of se...
lingkes2006 Linux and Android
Stepper drive_Stepper drive
Stepper drive Stepper drive...
wangwei20060608 MCU
LM4F program protection problem
I would like to ask, after the Flash Memory Protection Read Enable bit in LM4F230 is cleared, the corresponding block is prohibited from being read. Does it mean that it cannot be read as data in one'...
zhugean Microcontroller MCU
The SensorTile competition is still open for registration, the deadline is January 8th
[font=微软雅黑][size=4]Although the first batch of SensorTile finalists have been announced, the registration has not yet closed. [b]The deadline is January 8th[/b], [/size][/font][font=微软雅黑][size=4]Those...
nmg MEMS sensors
How to connect so that lpc1343 can write firmware via usb?
I don't know why, I designed it, after shorting jp1 and jp2, the computer always shows that the USB device cannot be recognized. Shouldn't it be recognized as a USB disk to upload firmware? I don't kn...
ssawee NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2116  168  9  2278  1458  43  4  1  46  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号