First Edition
Dec 12, 2005
LCD Module Technical Specification
Type No.
Final Revision
******
T-52017D121J-FW-A-AAN
Approved by (Quality Assurance Division)
Checked by (ACI Engineering Division)
Prepared by (ACI Engineering Division)
No.
--
1
2
3
4
5
6
7
8
9
10
11
12
--
--
--
CONTENTS
APPLICATION
OVERVIEW
Item
Page
1
2
3
4
4
7
9
14
15
17
19
20
21
24
29
30
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
INTERFACE PIN CONNECTION
INTERFACE TIMING
BLOCK DIAGRAM
MECHANICAL SPECIFICATION
OPTICAL CHARACTERISTICS
RELIABILITY TEST CONDITION
INSPECTION STANDARDS
HANDLING PRECAUTIONS FOR TFT-LCD MODULE
PACKGING SPECIFICATION
PRODUCTS NUMBER LABELING FORMS
LAMP UNIT FOR 12.1” SVGA
T-52017D121J-FW-A-AAN (AA) No. 2005-0433
OPTREX CORPORATION
Page 1/35
1. APPLICATION
This specification applies to color TFT-LCD module, T-52017D121J-FW-A-AAN.
These specification papers are the proprietary product of OPTREX and include materials protected
under copyright of OPTREX. No part of this document may be reproduced in any form or by any
means without the express written permission of OPTREX.
OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a product specified in this document. No
license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual
property rights of OPTREX or of others.
OPTREX classifies the usage of the TFT-LCD module as follows. Please confirm the usage before
using the product.
(1) Standard Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
(2) Special Usage
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
(3) Specific Usage
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control
systems, life support systems and any other equipment. OPTREX should make a contract
that stipulate apportionment of responsibilities between OPTREX and our customer.
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should contact OPTREX sales representative in advance.
OPTREX has been making continuous effort to improve the reliability of its products. Customers
should implement sufficient reliability design of their application equipments such as redundant
system design, fail-safe functions, anti-failure features.
OPTREX assumes no responsibility for any damage resulting from the use of the product that does
not comply with the instructions and the precautions specified in this document.
Please contact and consult a OPTREX sales representative for any questions regarding this product.
T-52017D121J-FW-A-AAN (AA) No. 2005-0433
OPTREX CORPORATION
Page 2/35
2. OVERVIEW
T-52017D121J-FW-A-AAN is 12.1” color TFT-LCD (Thin Film Transistor Liquid Crystal Display)
module composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 800
×
600, 262 K-color or 16.7 M-color images are displayed
on the 12.1” diagonal screen. Input power voltage is 3.3V for LCD driving.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 40MHz
clock cycle.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM
Display Area (mm)
Number of Dots
Pixel Pitch (mm)
Color Pixel Arrangement
Display Mode
Number of Color
Brightness (cd/m
2
)
Wide Viewing Angle Technology
Viewing Angle (CR
≥
10)
Surface Treatment
Electrical Interface
Optimum Viewing Angle(Contrast ratio)
Module Size (mm)
Module Mass (g)
Backlight Unit
SPECIFICATION
246.0(H)
×
184.5(V)
(12.106-inch diagonal)
800
×
3 (H)
×
600 (V)
0.3075 (H)
×
0.3075 (V)
RGB vertical stripe
Normally white TN
262 K(6 bit/color), 16.7 M(8 bit/color)
1000
Optical Compensation Film
-65~65° (H)
-75~45° (V)
Antiglare and hard-coating 3H
LVDS(6 bit/8 bit)
6 o’clock
280.0 (W)
×
219.0 (H)
×
17.8 (D)
1150
CCFL, 4-tubes, edge-light, replaceable
Characteristic value without any note is typical value.
T-52017D121J-FW-A-AAN (AA) No. 2005-0433
OPTREX CORPORATION
Page 3/35
3. ABSOLUTE MAXIMUM RATINGS
ITEM
Power Supply Voltage for LCD
Logic Input Voltage
Lamp Voltage
Lamp Current
Lamp Frequency
Operation Temperature(Panel)
Operation Temperature(Ambient)
Storage Temperature
Note 1,2)
Note 2)
Note 2)
SYMBOL
VCC
VI
VL
IL
FL
T
op(Panel)
T
op(Ambient)
T
stg
MIN.
0
−0.3
0
0
--
−20
−20
−20
MAX
4.0
VCC+0.3
2000
18
80
70
70
80
UNIT
V
V
Vrms
mArms
kHz
°C
°C
°C
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg
≤
40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than the value of 90%RH at 40°C without
condensation.
4. ELECTRICAL CHARACTERISTICS
(1) TFT-LCD
Ambient temperature: Ta = 25℃
ITEM
Power Supply Voltages for LCD
Power Supply Currents for LCD
Permissive Input Ripple Voltage
*1) Power and signals sequence:
t1
≤
10 ms
0 < t2
≤
50 ms
0 < t3
≤
50 ms
SYMBOL
VCC
ICC
VRP
200 ms
≤
t4
200 ms
≤
t5
0
≤
t6
MIN.
3.0
--
--
TYP.
3.3
300
--
MAX.
3.6
450
100
UNIT
V
mA
mVp-p
Remarks
*1)
VCC = 3.3 V
*2)
VCC = 3.3V
VCC
LCD Power Supply
0.9VC C
data
0.9VC C
0.1VC C
0.1VCC
Logic Signal
0.1VCC
t1
t2
Backlight
t3
t4
Backlight Power Supply
t5
t6
data: R G B DATA, DCLK, DENA
T-52017D121J-FW-A-AAN (AA) No. 2005-0433
OPTREX CORPORATION
Page 4/35
VCC-dip conditions:
1) When 2.6 V
≤
VCC < 3.0 V, td
≤
10 ms
2) When VCC < 2.6 V
VCC-dip conditions should also follow the power and signals sequence.
VCC
td
*2) Typical current condition:
64-gray-bar pattern
600 line mode
VCC = +3.3 V , f
H
=37.9 kHz, f
V
=60.0 Hz, f
CLK
= 40 MHz
(2) Backlight
Ta = 25℃
ITEM
Lamp Voltage
Lamp Current
Lamp Frequency
Starting Lamp Voltage
SYMBOL
MIN.
--
6.0
30
1000
1200
1290
TYP.
540
12.0
--
--
--
--
--
2.6V
3.0V
MAX.
--
14.0
60
--
--
--
--
UNIT
Vrms
mArms
kHz
Vrms
Remarks
IL = 12.0 mArms
* 2), *6)
* 3)
VL
IL
FL
VS
Ta = 25°C
Ta = 0°C
Ta =
−20°C
h
* 4), *5)
IL
Lamp Life Time
LT
50,000
= 12.0mArms,
Continuous operation
[Note]
*1)Please use synchronous inverter.
*2) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL
CTH
A
LCD
Module
CTH
CTH
CTH
CTL
Power
Inverter
Supply
A
*3) Lamp frequency of inverter may produce interference with horizontal synchronous frequency,
and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and keep
inverter as far from module as possible or use electronic shielding between inverter and module to
avoid the interference.
T-52017D121J-FW-A-AAN (AA) No. 2005-0433
OPTREX CORPORATION
Page 5/35
京公网安备 11010802033920号
EEWORLD
