WBC-T0303GS-03-2212-FG datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> WBC-T0303GS-03-2212-FG

WBC-T0303GS-03-2212-FG: DescriptionArray/Network Resistor, Center Tap, Thin Film, 0.25W, 22100ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,; CategoryPassive components The resistor; File Size376KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

WBC-T0303GS-03-2212-FG Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 22100ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303GS-03-2212-FG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	802733307
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
resistance	22100 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC(TAPPED)
size code	0303
technology	THIN FILM
Temperature Coefficient	25 ppm/°C
Tolerance	1%
Operating Voltage	100 V

Preview

Download Datasheet

View All

Wire Bondable

Chip Resistors

WBC Series

•

Discrete or tapped schematics

•

MIL inspection available

•

High resistor density

IRC Advanced Film Division

IRC’s WBC series wire bondable chip resistors are ideally suited for

the most demanding hybrid application. The WBC combines IRC’s

TaNSil

tantalum nitride thin ﬁlm technology with silicon substrate processing to produce an extremely small

footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil

resistor ﬁlm.

Available in a wide range of tolerances and temperature coefﬁcients to ﬁt a variety of hybrid circuit applica-

tions. Custom resistance values, sizes and schematics are available on request from the factory.

Physical Data

R0202 - Discrete

(0.508mm ±0.025)

0.020˝ ±0.001

Electrical Data

Absolute Tolerance

Absolute TCR

Package Power Rating

(@ 70°C)

Rated Operating Voltage

(not to exceed

√

P x R )

Operating Temperature

Back contact

Noise

Substrate Material

Top contact

Substrate Thickness

Aluminum

Gold

R0202 and

T0303

B0202

Passivation

to ±0.1%

to ±25ppm/°C

250mW

100V

-55°C to +150°C

<-30dB

Oxidized Silicon

(10KÅ SiO

min)

0.010˝ ±0.001

(0.254mm ±0.025)

10KÅ minimum

15KÅ minimum

Silicon

(Gold available)

Gold

3KÅ minimum

Silicon Dioxide or

Silicon Nitride

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

B0202 - Discrete back contact

(0.508mm ±0.025)

0.020˝ ±0.001

Top contact

pad chamfered

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

T0303 - Tapped network ½R + ½R

Bond Pad

Metallization

(0.762mm ±0.025)

0.030˝ ±0.001

Backside

½R

0.030˝ ±0.001

(0.762mm ±0.025)

0.004˝ min bond pad size

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com

A subsidiary of

TT electronics plc

WBC Series Issue April 2006

Recommended Resources

Internal circuit principle of LB1419

Sound and light controlled staircase delay switch circuit using op amp

Timing trigger switch circuit

Ring detector circuit

4052B for symmetrical input multiplexing systems

Zero sequence voltage motor phase failure protection circuit

The wireless network card cannot refresh the network list. How to solve it?: My laptop has been connected to the wireless network (automatically connected to the wireless router) for a few days. Today, the wireless connection shows that it is not connected and the network list...; han0602 Embedded System

Application of Current Controlled Pulse Width Modulator UC3842 in Switching Power Supply: [i=s] This post was last edited by paulhyde on 2014-9-15 09:21 [/i] Introduction The switching power supply is known as the "new type of high-efficiency and energy-saving power supply", and it represe...; dtcxn Electronics Design Contest

pcba storage conditions (temperature, humidity): Does anyone have any documentation on pcba storage conditions? Thanks a lot...; 刘123 PCB Design

Problem with branch instruction B in ARM: Why is B limited to the range of plus or minus 32MB of the current instruction? Also, ARM instructions are word-aligned, and the lowest 2 bits of the address are fixed to 0. What does this mean? I loo...; linwj ARM Technology

Why does the voltage on the pin become 2.2V when the 3.3V power supply made of a voltage zener diode is used to power the microcontroller?: I changed R1 to 270 ohms. When it is 470 ohms, the output voltage is only 3.1V. 270 ohms is just 3.3V! But when it is connected to the VCC of the microcontroller, it becomes 2.2V. Do I need to add a v...; 278023330 Microcontroller MCU

Looking for Keil crack limit to 8k or unlimited!: Many keil cracked software have restrictions (2k)! When writing programs, they are often limited, and the functions cannot be fully displayed when used!...; 645715899 MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components