Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
VC
10nF
1nF
1
6
Receiver
100
3
4
3
4
1
6
10nF
100
Receiver
VC
+3.3V
10nF
1nF
OE
2
5
OE
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Cause: I need to do an experiment of acceleration sensor for work. The fastest time for PCB manufacturer to make the board is 1 week (expedited). Usually it takes 1-2 weeks to delay the development cy...
Other emulators already support Keil C V8~9, why is Weifu's emulator still stuck at V4~5? It has been almost 10 years since WAVE6000 to V8, and Weifu still has no improvement?...
[hide]To design a product, we must first determine whose LED package structure to use; then consider how to adapt to these packages; We have few opportunities to choose, and the optical structure is b...
The competition is about to begin. [size=5][b]EEWORLD community wishes all the friends participating in the forum to relax and achieve good results. [/b][/size] If you have any questions, you are welc...
I have a problem. If the value of SWWSR for software waiting for external memory is set to greater than 2, CCS will report an error:"Trouble Halting Target CPU: Timeout on Target Processor". After tha...
I am making components, but I don't know how to choose the electrical type of the component pins, which always leads to production failure. I would like to ask you, what do these electrical types of p...
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1 Introduction
PROFIBUS is an international, open, and manufacturer-independent fieldbus standard. It is widely used in manufacturing automation, process industry automation, and automatio...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
0 Introduction
Under normal circumstances, the three-phase power in the power system is symmetrical, and they meet certain amplitude and phase conditions; but when the load changes, the syst...[Details]
Rated capacity refers to the maximum output power of the UPS (the product of voltage V and current A).
Usually, the UPS power supplies sold on the market are marked with "W" (watt) for smaller...[Details]
The battery and its management system are one of the key technologies of electric vehicles. In the past few years, most companies have encountered embarrassment in the development of electric vehic...[Details]
The cruise control system (CCS) of a vehicle is also called a constant speed driving system. It is an electronic control device that uses advanced electronic technology to automatically adjust the ...[Details]
Introduction
Every year, cars are equipped with more complex electronic systems to maximize comfort, safety, and performance while minimizing harmful emissions. According to market resea...[Details]
O Introduction
Virtual instrument is a new type of instrument developed with
the development of
computer
technology, electronic measurement technology and communication technology. ...[Details]
When selecting EMC test equipment, we often encounter the following questions: What is the difference between an EMI receiver and a spectrum analyzer? Why should a receiver be used for EMI testing?...[Details]
1. Overview
Infrared temperature measurement technology plays an important role in product quality control and monitoring, online equipment fault diagnosis and safety protection, and energy co...[Details]
This paper mainly studies the parallel current sharing technology of Droop method DC/DC converters, and designs a current sharing converter with parallel output of two DC/DC converters based ...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
