EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

CHP2208K2051FGTA

Description
Fixed Resistor, Metal Glaze/thick Film, 0.75W, 2050ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2208, CHIP
CategoryPassive components    The resistor   
File Size146KB,9 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

CHP2208K2051FGTA Overview

Fixed Resistor, Metal Glaze/thick Film, 0.75W, 2050ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2208, CHIP

CHP2208K2051FGTA Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid145113590946
package instructionSMT, 2208
Reach Compliance Codeunknown
Country Of OriginFrance
ECCN codeEAR99
YTEOL7.8
structureRectangular
JESD-609 codee4
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length5.53 mm
Package formSMT
Package width2.05 mm
method of packingTR, PLASTIC
Rated power dissipation(P)0.75 W
Rated temperature70 °C
resistance2050 Ω
Resistor typeFIXED RESISTOR
size code2208
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage200 V
The board has been soldered, let me show it to you and ask a question.
The board is soldered. It went pretty smoothly. I took some pictures to show off. There is another small problem. I found that some capacitor positions on the circuit board are empty. Is it better to ...
daijun DIY/Open Source Hardware
WINCE6 calls the dial-up software and reports error 633
I am debugging a TD module with PCIE interface on wince6. The manufacturer provides a driver. The driver is modified to simulate three serial ports, COM6, COM7, and COM8. COM6 may have a problem in lo...
panxin Embedded System
There is a 5V signal outside the cyclone iii. How should it be set to be compatible?
The cyclone iii has an external 5V signal. How should I set it to be compatible? It is a control of an AD7891 AD chip. The logic level is 5V. A 1k resistor is connected to the data channel. The input ...
eeleader FPGA/CPLD
Caution! Don’t be fooled by long-term drift and hysteresis of voltage references
[i=s]This post was last edited by qwqwqw2088 on 2019-2-20 09:39[/i] [size=4] The LT1461 and LT1790 micropower low dropout bandgap voltage references excel not only in temperature coefficient (TC) and ...
qwqwqw2088 Analogue and Mixed Signal
Using nRF51822 module to make BLE packet capture device
[i=s]This post was last edited by le062 on 2017-4-17 17:19[/i] [md]### Why do you need to DIY a packet grabber? The [KW41Z activity]([url=https://www.eeworld.com.cn/huodong/201611_NXPKW41ZActivity1/in...
le062 RF/Wirelessly
Typical circuit of LM258 op amp
I don't understand the schematic diagram, can you explain it to me?...
往死里学 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 273  1162  1687  2598  493  6  24  34  53  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号