INTEGRATED CIRCUITS
DATA SHEET
TDA8001
Smart card interface
Product specification
Supersedes data of 1995 Feb 01
File under Integrated Circuits, IC02
1996 Dec 12
Philips Semiconductors
Product specification
Smart card interface
FEATURES
•
Protected I/O line
•
V
CC
regulation (5 V
±5%,
100 mA max. with controlled
rise and fall times)
•
V
PP
generation (12.5, 15 or 21 V
±2.5%,
50 mA max.,
with controlled rise and fall times) (only at TDA8001 and
TDA8001T)
•
Clock generation (up to 10 MHz), with synchronous
frequency doubling
•
Overload, thermal and card extraction protections
•
Current limitation in case of short-circuit
•
Idle mode and special circuitry for spikes killing during
powering on and off
•
Two voltage supervisors (digital and analog supplies)
•
Automatic activation and deactivation sequences
through an independent internal clock
•
Enhanced ESD protections on card side (4 kV min.)
•
Easy chaining for multiple card readers
•
ISO 7816 compatibility.
ORDERING INFORMATION
TYPE
NUMBER
TDA8001;
TDA8001A
TDA8001T;
TDA8001AT
PACKAGE
NAME
DIP28
SO28
DESCRIPTION
plastic dual in-line package; 28 leads (600 mil)
plastic small outline package; 28 leads; body width 7.5 mm
APPLICATIONS
TDA8001
•
Pay TV (multistandards conditional access system,
videoguard, newscript)
•
Multi-application smart card readers (banking, vending
machine, electronic payment identification).
GENERAL DESCRIPTION
The TDA8001 is a complete, low-cost analog interface
which can be positioned between an asynchronous smart
card (ISO 7816) and a microcontroller. It is directly
compatible with the new Datacom chip verifier.
The complete supply, protection and control functions are
realized with only a few external components, making this
product very attractive for consumer applications
(see Chapter “Application information”).
VERSION
SOT117-1
SOT136-1
1996 Dec 12
2
Philips Semiconductors
Product specification
Smart card interface
QUICK REFERENCE DATA
SYMBOL
V
DD
I
DD
V
th2
V
th4
V
CC
I
CC
PARAMETER
supply voltage
supply current
threshold voltage on V
SUP
threshold voltage on V
DD
card supply voltage
card supply current
including static and dynamic
loads on 100 nF capacitor
operating
detection
limitation
V
H
V
PP
high voltage supply for
V
PP
card programming
voltage (only at TDA8001
and TDA8001T)
(P = 5, 12.5, 15 and 21 V)
programming current
(read or write mode)
including static and dynamic
loads on 100 nF capacitor
idle mode; V
DD
= 12 V
active modes; unloaded
CONDITIONS
−
−
4.5
6
4.75
−
−
−
−
MIN.
6.7
−
32
45
−
−
5.0
−
−150
−
−
TYP.
−
−
TDA8001
MAX.
18
UNIT
V
mA
mA
V
V
V
mA
mA
mA
V
4.72
6.5
5.25
−100
−
−200
30
P
−
2.5%
−
P + 2.5% V
I
PP
operating
detection
limitation
−
−
−
−
−75
−
0.38
100
−
−
−
−
−50
−
−100
−
125
8
0.92
2
+70
mA
mA
mA
V/µs
µs
MHz
W
W
°C
SR
t
de
f
clk
P
tot
slew rate on V
CC
and V
PP
(rise and fall)
deactivation cycle duration
clock frequency
continuous total power
dissipation
maximum load capacitor 150 nF
−
75
0
TDA8001; T
amb
= +70
°C;
see Fig.10
TDA8001T; T
amb
= +70
°C;
see Fig.11
−
−
0
T
amb
operating ambient
temperature
1996 Dec 12
3
Philips Semiconductors
Product specification
Smart card interface
BLOCK DIAGRAM
TDA8001
handbook, full pagewidth
VSUP
15
ALARM
ALARM
17
18
DELAY
16
VDD
13
GND1
12
22
VOLTAGE
SUPERVISOR
MAIN
SUPPLY
CVNC
I/O(µC)
28
PROTECTIONS
AND
ENABLE
3
I/O
RSTIN
26
4
RST
TDA8001
19
OFF
2
DETECT
INTERNAL
CLOCK
20
27
CMD7
25
GND2
23
CMD3.5
CLKOUT2
VPP12.5
VPP15
VPP21
24
6
7
21
VPP
GENERATOR
CLOCK
CIRCUITRY
CLOCK
ENABLE
PROTECTIONS
LOGIC
9
8
PRES
PRES
CMDVCC
VCC
GENERATOR
14
VCC
5
CLK
10
VPP
OSCILLATOR
1
XTAL
11
MBH813
VH
Fig.1 Block diagram.
1996 Dec 12
4
Philips Semiconductors
Product specification
Smart card interface
PINNING
PIN
SYMBOL
XTAL
DETECT
I/O
RST
CLK
VPP12.5
n.c.
VPP15
n.c.
PRES
PRES
V
PP
n.c.
V
H
GND1
V
DD
V
CC
V
SUP
DELAY
ALARM
ALARM
OFF
CMDVCC
VPP21
n.c.
CVNC
CMD3.5
or CDMTC
CLKOUT2
GND2
RSTIN
CMD7
or CDMS
I/O(µC)
TDA8001
TDA8001T
1
2
3
4
5
6
−
7
−
8
9
10
−
11
12
13
14
15
16
17
18
19
20
21
−
22
23
24
25
26
27
28
TDA8001A
TDA8001AT
1
2
3
4
5
−
6
−
7
8
9
−
10
11
12
13
14
15
16
17
18
19
20
−
21
22
23
24
25
26
27
28
crystal connection
card extraction open collector output (active LOW)
data line to/from the card
card reset output
clock output to the card
DESCRIPTION
TDA8001
control input for applying the 12.5 V programming voltage (active LOW)
not connected
control input for applying the 15 V programming voltage (active LOW)
not connected
card presence contact input (active LOW)
card presence contact input (active HIGH)
card programming voltage output
not connected
HIGH voltage supply for V
PP
generation
ground 1
positive supply voltage
card supply output voltage
voltage supervisor input
external capacitor connection for delayed reset timing
open-collector reset output for the microcontroller (active HIGH)
open-collector reset output for the microcontroller (active LOW)
open-collector interrupt output to the microcontroller (active LOW)
control input for applying supply voltage to the card (active LOW)
control input for applying the 21 V programming voltage (active LOW)
not connected
internally generated 5 V reference, present when V
DD
is on; to be
decoupled externally (100 nF)
control input for having the crystal frequency divided-by-4 at pin CLK
clock output to the microcontroller, or any other R4590
(crystal frequency divided by two)
ground 2
card reset input from the microcontroller (active HIGH)
control input for having the crystal frequency divided by 2 at pin CLK
data line to/from the microcontroller
1996 Dec 12
5
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
