As the title says, I made a signal conditioning board, two of which are speed channels. I made an adapter to convert the 4-20MA current signal into a 1-5V voltage signal, and added a resistor. Can thi...
I use the serial port to send an array, the sending function is as follows: void Uart_Init() //Initialize UART { SCON =0x58; //Select the serial port working mode, turn on the receiving permission TMO...
A C6746 project was built in CCS3.3, and the relevant registers were defined in the header file extern cregister volatile Uint32 AMR; /* Address Mode Register */ extern cregister volatile Uint32 CSR; ...
I recently read a book and found an example of using FPGA to implement UART communication. So I tried it on my own experimental board. But there is one problem that has not been solved: my clock is 50...
Click save once every 5 minutes and back up the working project folder twice each time!No matter it's software design or hardware design, or something else, anyway, once you open the software, you hav...
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
The day before yesterday, I learned about STM's Systick and found it quite useful for precise timing. When I used CVAVR before, I found that the delay.h in it was very useful. So, I used STM32's...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
introduction STM32 has many registers, which are difficult to remember, so the official packaged two sets of library functions. One is the standard library, but the official has not updated it on F7,...[Details]
The last two blogs talked about a version problem of STM32CubeMX and the problem of hardware reset. When you solve these two problems, you will find that after the program is burned into the board, t...[Details]
Automotive LCD Instrument Clock EMI Solution As early as 2014, the market size of China's automotive full LCD instrument has reached 3.506 billion yuan, and it is expected that by 2020, this s...[Details]
Superconductors have physical properties such as zero resistance effect, Meissner effect and Josephson effect, which make them have broad application prospects and unparalleled advantages in many b...[Details]
Analysts have sorted out some interesting phenomena. Let's follow the embedded editor to learn about the relevant content.
Huawei emerged as a star in the all-
flash
array sales ra...[Details]
Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
As a leading company in automotive semiconductors, Freescale and Khronos Group have jointly launched an automotive multimedia embedded microprocessor i.MX35 with an integrated OpenVG hardware acceler...[Details]
Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]
1) Independent watchdog has no interrupt, window watchdog has interrupt 2) Independent watchdogs can be divided into hardware and software, while window watchdogs can only be controlled by software...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]